Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Great Bellows of the Smelting Works: Pine Boards, Linden Bows, Ox-Hide and Iron Nozzle (Agricola, 1556)
Forge

Dicipta oleh

Forge

14. November 2026NO
11
0
0
0
0

Great Bellows of the Smelting Works: Pine Boards, Linden Bows, Ox-Hide and Iron Nozzle (Agricola, 1556)

The large blast bellows of a 16th-century smelting works, every part measured, from Agricola's De Re Metallica, Book IX (1556): two tapered boards of glued pine edged with linden, about 1.7 m long, two linden bows, two ox-hides nailed on with T-headed nails, a goatskin flap valve in the lower board, and a glued head carrying a 3 ft iron nozzle.
Lanjutan
About 2 weeks

Arahan

1

Roman units in metric

Memuatkan buku nota Jupyter…
2

Read De Re Metallica, Book IX

"Each bellows consists of a body and a head. The body is composed of two 'boards', two bows, and two hides."
3

Make the upper board

Glue two pieces of pine into a board a palm thick, 5 ft 3 palms long, 2-1/2 ft wide at the back (sides a little curved) and a cubit wide at the front, tapering to the head. Glue on linden edge strips, 7 digits wide at the back and 1-1/2 at the front, to take the nails. Cut an aperture 6 by 4 digits in the middle, 1 ft 3 palms from the head, with a sliding lid 2 palms 1 digit square and 3 digits thick running in mouldings a palm wide and 3 digits thick (or bore 2-3 round holes with plugs). Glue and peg a handle 7 palms or longer (2 palms wide, 1 thick on the board; rounded and 7 digits thick beyond), with a 2 ft cleat 2 palms wide and a palm thick over it and another 2 ft cleat underneath, 3 palms from the end.

Bahan untuk langkah ini:

Papan painPapan pain2 keping
Kepingan kayu basswoodKepingan kayu basswood1 keping
Gam kulit haiwanGam kulit haiwan1 keping
Rod Pasak KayuRod Pasak Kayu1 keping

Alatan diperlukan:

Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Pahat kayuPahat kayu
Gerimit engkol dan mataGerimit engkol dan mata
Pengapit barPengapit bar
4

Make the lower board and flap valve

Make the lower board the same way and a cubit longer (the extra length is part of the head). About a cubit from the back, centred, cut an air-hole a foot long and 3 palms wide, leaving a rib a palm long and 1/3 digit wide across it. Make the flap a foot 3 digits by 3 palms 3 digits of thin board covered with goatskin, hair toward the ground, hinged with a doubled strip of leather a palm wide nailed to it and tied through two holes 7 digits apart. A foot beyond, fix a slightly elliptical iron ring 2 palms by 1 on a staple, 3 palms from the back, for the wooden bolt that holds the board to its frame (or use two iron screws).

Bahan untuk langkah ini:

Papan painPapan pain2 keping
Kepingan kayu basswoodKepingan kayu basswood1 keping
Gam kulit haiwanGam kulit haiwan1 keping
Kulit kambing mentahKulit kambing mentah1 keping
Tali kulitTali kulit1 keping
Gelang logamGelang logam1 keping
PakuPaku1 keping

Alatan diperlukan:

Gergaji TanganGergaji Tangan
Pahat kayuPahat kayu
Gerimit engkol dan mataGerimit engkol dan mata
TukulTukul
5

Make the bows

Make each bow as long as the upper board from four pieces of linden 3 digits thick: two long pieces 7 digits wide at the back and 2-1/2 at the front, a back piece 2 palms wide, its ends a little over a digit thick, bent to meet the long pieces, mortised, bored and pegged with glued pegs. Mortise in a crossbar a cubit from the head, a foot long without tenons and a palm 2 digits wide. Glue and peg two small pieces, 3 palms 2 digits long, a palm high and a digit thick, at the head to keep the bow ends off the air passage.

Bahan untuk langkah ini:

Kepingan kayu basswoodKepingan kayu basswood2 keping
Gam kulit haiwanGam kulit haiwan1 keping
Rod Pasak KayuRod Pasak Kayu1 keping

Alatan diperlukan:

Gergaji TanganGergaji Tangan
Pahat kayuPahat kayu
Gerimit engkol dan mataGerimit engkol dan mata
Tukul KayuTukul Kayu
6

Make the head and nozzle

Glue the upper head board, a cubit long and 1-1/2 palms thick, onto the lower board's extension (a palm and a digit thick). Shape it a cubit wide at the back, 2 digits narrower 3 palms forward, then round the front to 2 palms 2 digits across and bind it with an iron ring 3 digits wide. Bore it for the nozzle: a pipe of thin iron plate 3 ft long, 3 digits across in front and a palm high by 2 palms wide at the back.

Bahan untuk langkah ini:

Papan painPapan pain1 keping
Gam kulit haiwanGam kulit haiwan1 keping
Kepingan besi (ditempa)Kepingan besi (ditempa)1 keping
Gelang logamGelang logam1 keping

Alatan diperlukan:

Gergaji TanganGergaji Tangan
Gerimit engkol dan mataGerimit engkol dan mata
Relau TempaRelau Tempa
AndasAndas
TukulTukul
7

Hide the bellows

Use ox-hide (far better than horse), two hides each 3-1/2 ft wide at the back. Lay a long leather thong along each board and bow and nail the hide through it with T-shaped iron nails 5 digits long, horns 2-1/2 digits long and half a digit wide, the horn of one nail almost touching the next along the boards; on each bow two nails in the back piece and four in each long piece, ten in all. Pine strips nailed over the hide on the long pieces guard against tearing; iron screws through strips over the hide hold even better.

Bahan untuk langkah ini:

Kulit samak tumbuhanKulit samak tumbuhan2 keping
Tali kulitTali kulit1 keping
PakuPaku1 keping

Alatan diperlukan:

TukulTukul
Pisau kulitPisau kulit
GuntingGunting
8

Troubleshooting

Bellows troubleshooting.

Flow

Loading...
9

History and honest limits

From Georgius Agricola, **De Re Metallica** (1556), Book IX, translated by Herbert C. and Lou H. Hoover, 1912 (checked on the archive.org scan georgiusagricola00agri, pp. 362-365). The frame and the machinery that work the bellows are not covered here. The metric conversions (digit ~1.85 cm, palm ~7.4 cm, Roman foot ~29.6 cm, cubit ~44.4 cm) and the tools are ours.

Bahan

10

Alatan Diperlukan

11

Blueprint berkaitan

Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...