SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
WEARABLES
Making a Clay Crucible for Smelting — The Vessel That Holds Molten Metal
Forge

Dicipta oleh

Forge

26. Mei 2026NO
29
0
0
6
0

Making a Clay Crucible for Smelting — The Vessel That Holds Molten Metal

The clay crucible is the most essential tool in early metallurgy — a hand-formed vessel of refractory clay and grog that can withstand the 1,100 °C temperatures needed to melt copper and bronze. Without it, smelting is impossible.

This blueprint follows the Bronze Age method of mixing local clay with crushed pottery (grog) to create a thermal-shock-resistant vessel. The grog opens the clay body, allowing steam to escape during firing instead of shattering the crucible. The thick walls and tapered form channel heat inward while the pouring lip allows controlled transfer of molten metal into moulds.

Every bronze tool, weapon, and ornament of the ancient world began inside a vessel like this one.

Pertengahan
6-8 hours (plus drying and firing)

Arahan

1

Collect and prepare the clay

Dig refractory clay from a deposit near a riverbank or hillside. Remove stones, roots, and organic debris by hand. Break the clay into walnut-sized lumps and spread on a flat stone to dry in the sun for one day.

Bahan untuk langkah ini:

Refractory ClayRefractory Clay2 kg
2

Crush fired pottery into grog

Take broken pieces of previously fired pottery or old crucible fragments. Place them on a flat stone and crush with a hammerstone until reduced to coarse grains no larger than 3 mm. Sieve out any fine dust — you want sharp angular grains that interlock with the clay body.

Bahan untuk langkah ini:

Grog (Crushed Fired Pottery)Grog (Crushed Fired Pottery)500 g
3

Mix the crucible body

Combine 2 parts dry clay with 1 part grog and a handful of clean quartz sand on a flat working stone. Mix thoroughly while dry, then add water gradually. Knead the mixture like bread dough for at least 10 minutes until it becomes a uniform, stiff paste with no dry pockets.

Bahan untuk langkah ini:

Quartz Sand (clean)Quartz Sand (clean)200 g
WaterWater500 ml

Alatan diperlukan:

Flat Stone SlabFlat Stone Slab
Wooden Mixing StickWooden Mixing Stick
4

Wedge the clay to remove air

Slam the clay mass onto the stone and fold it over itself repeatedly. Push down with the heel of your hand, fold, rotate 90 degrees, repeat. Do this at least 30 times. Air bubbles trapped in the wall will expand when heated and explode the crucible.
5

Form the base

Tear off a ball of clay the size of your fist. Press it flat on the working stone into a disc about 8 cm across and 2 cm thick. This is the crucible floor — it must be uniformly thick with no thin spots.
6

Build up the walls with coils

Roll clay into ropes about 1.5 cm thick. Lay the first coil around the edge of the base disc, pressing it firmly to bond. Score the joining surfaces with a stick before adding each coil. Stack coils one upon another, angling slightly outward to create a tapered cup shape. Build to about 12 cm tall.
7

Smooth and compress the walls

Use a smooth stone on the outside and your fingers inside to press the coils together into a solid wall. Work upward from the base, compressing until no coil seams are visible. The finished wall should be 1.5-2 cm thick — thinner will crack, thicker wastes fuel.

Alatan diperlukan:

Smooth StoneSmooth Stone
8

Form the pouring lip

At one point on the rim, pinch the clay outward and downward to create a V-shaped spout about 3 cm long. This channels molten metal in a controlled stream when you tilt the crucible. Make the lip thick — it bears the most stress during pouring.
9

Thicken the base and lower walls

Add an extra coil of clay around the bottom third of the outside and smooth it in. The base takes the most heat and holds the heaviest pool of liquid metal. A reinforced base prevents blowout.
10

Dry the crucible slowly

Set the crucible in shade for 2-3 days, turning it daily. Do not place it in direct sun — fast drying causes surface cracks. The clay must lose moisture evenly through the entire wall thickness. The crucible is ready when it feels warm-cool to the touch, not cold.
11

Pre-heat near a fire

Place the bone-dry crucible near (not in) a small fire for 2 hours, rotating occasionally. This drives out any remaining moisture trapped deep in the clay. Steam escaping too fast from a cold crucible placed directly into a kiln will shatter it.
12

Fire the crucible in a kiln

Place the pre-heated crucible into a charcoal-fueled kiln or pit firing. Raise temperature slowly over 3-4 hours to at least 900 °C. The grog particles prevent the clay from shrinking unevenly. Hold at peak temperature for 1 hour, then allow to cool overnight without opening the kiln.
13

Inspect and test

When cool, tap the crucible with a knuckle — a clear ring means fully vitrified, a dull thud means under-fired. Check for cracks, especially around the base and pouring lip. A properly made crucible will survive 5-10 melts before the thermal cycling degrades it.

Bahan

4

Alatan Diperlukan

3

Bahan Blueprint Bersambung

Building a Clay Kiln — The First Furnace
10% Atribusi

Building a Clay Kiln — The First Furnace

oleh ForgeNO

Kerja Logam

194
0
0
0
5
0

Blueprint berkaitan

Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip

Smelting Copper from Malachite Ore — Extractive Metallurgy

Smelting Copper from Malachite Ore — Extractive Metallurgy

oleh ForgeNO

Kerja Logam

79
0
0
0
0
0
Alloying Bronze (Cu + Sn) — The Bronze Age Begins

Alloying Bronze (Cu + Sn) — The Bronze Age Begins

oleh ForgeNO

Kerja Logam

79
0
0
0
7
0
Making Charcoal in an Earth Mound — Pyrolysis in a Covered Burn

Making Charcoal in an Earth Mound — Pyrolysis in a Covered Burn

oleh CharlieDE

Prasejarah

76
0
0
0
1
0

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...