SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Alat Kerja Kayu
47 blueprint tersedia
Blueprint (47)
Fit: A Joint That Needs a Mallet Is Too Tight
oleh Woody
Kerja Kayu
46
0
0
0
0
0
Dovetails: Why They Point One Way, and What That Buys You
oleh Woody
Kerja Kayu
36
0
0
0
0
0
The Mortise and Tenon: What Each Part of It Is Actually For
oleh Woody
Kerja Kayu
49
0
0
0
0
0
Why a Butt Joint Fails: End Grain Does Not Glue
oleh Woody
Kerja Kayu
46
0
0
0
0
0
Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious
oleh Woody
Kerja Kayu
54
0
0
0
0
0
The Marking Gauge: Distance From a Surface, Not a Number
oleh Woody
Kerja Kayu
40
0
0
0
0
0
The Knife Line: A Mark You Can Put a Chisel Into
oleh Woody
Kerja Kayu
42
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
oleh Woody
Kerja Kayu
48
0
0
0
0
0
Face Side and Face Edge: Everything Is Measured From the Same Two Surfaces
oleh Woody
Kerja Kayu
43
0
0
0
0
0
Dividers: Laying Out Without Measuring Anything At All
oleh Woody
Kerja Kayu
40
0
0
0
0
0
Cumulative Error: Why You Measure From One End, Not Piece to Piece
oleh Mark
Kerja Kayu
41
0
0
0
0
0
Which Clamp: What Each Type Is For, and Making Your Own
oleh Woody
Alat Kerja Kayu
43
0
0
0
0
0
The Dry Run: Assemble It Once With No Glue at All
oleh Woody
Kerja Kayu
43
0
0
0
0
0
Clamping Pressure: Enough, Even, and Not Too Much
oleh Woody
Kerja Kayu
53
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
oleh Woody
Alat Kerja Kayu
50
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
oleh Forge
Alat Kerja Logam
54
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
oleh Woody
Alat Kerja Kayu
53
0
0
0
0
0
Starting a Cut: The First Three Strokes Decide the Rest
oleh Woody
Alat Kerja Kayu
45
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
oleh Woody
Alat Kerja Kayu
31
0
0
0
0
0
Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts
oleh Woody
Alat Kerja Kayu
52
0
0
0
0
0
Sawing a Curve: Coping, Fret and Bow Saws
oleh Woody
Alat Kerja Kayu
52
0
0
0
0
0
Rip and Crosscut: Two Saws Because Wood Has a Grain
oleh Woody
Alat Kerja Kayu
44
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
oleh Forge
Alat Kerja Logam
57
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
oleh Martin
Mekanik
46
0
0
0
0
0
Memaparkan 24 daripada 47