SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Multi-Conductor Cable: Cotton-Covered, Waxed and Twisted
Penny

Dicipta oleh

Penny

14. Oktober 2026DK
14
0
0
0
0

Multi-Conductor Cable: Cotton-Covered, Waxed and Twisted

A cable of several insulated wires in one bundle, such as the four leads of a strain-gauge bridge. Each copper wire is wrapped in cotton thread and soaked in beeswax, then the wires are twisted together and covered again.
Pemula
An afternoon

Arahan

1

Cut the conductors

Cut one copper wire per conductor (four for a bridge), a little longer than the cable.

Bahan untuk langkah ini:

Dawai TembagaDawai Tembaga4 length

Alatan diperlukan:

Playar pelucut wayarPlayar pelucut wayar
2

Wrap each wire in cotton

Clamp one end in the vise and the other in the hand drill's chuck, keeping it taut. Wind cotton thread on in a close spiral with no gaps, then a second layer the opposite way.

Bahan untuk langkah ini:

Benang KapasBenang Kapas1 as required

Alatan diperlukan:

Ragum BangkuRagum Bangku
Gerimit tanganGerimit tangan
GuntingGunting
3

Soak in beeswax

Melt beeswax in a double boiler and draw each covered wire slowly through it. Wipe off the excess and let it set.

Bahan untuk langkah ini:

Lilin LebahLilin Lebah1 as required

Alatan diperlukan:

Periuk tanak dua lapisPeriuk tanak dua lapis
Plat PemanasPlat Pemanas
4

Twist them together

Lay the covered wires side by side, clamp one end and twist them together evenly with the drill.

Alatan diperlukan:

Ragum BangkuRagum Bangku
Gerimit tanganGerimit tangan
5

Cover the bundle

Wind an outer layer of cotton over the twisted bundle and wax it again.

Bahan untuk langkah ini:

Benang KapasBenang Kapas1 as required
Lilin LebahLilin Lebah1 as required

Alatan diperlukan:

Ragum BangkuRagum Bangku
Periuk tanak dua lapisPeriuk tanak dua lapis
Plat PemanasPlat Pemanas
6

Test it

Strip the ends. With a multimeter check each wire end to end, and check that no two wires touch.

Alatan diperlukan:

Playar pelucut wayarPlayar pelucut wayar
MultimeterMultimeter
7

Limits

Cotton insulation is only good for low temperatures, up to about 105 °C (Wikipedia, Magnet wire), and for dry places and low voltages such as instrument leads. The method is general workshop practice, ours.

Bahan

3
  • Pemegang Tempat
  • 2 as required
    Pemegang Tempat
  • 2 as required
    Pemegang Tempat

Alatan Diperlukan

7

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...