Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)
An automatic electric kettle boils water with an immersion heater and switches itself off. J. C. Taylor (US 4,358,666, 1982) mounts one control on the heater's head: a bimetal disc touching the hot head cuts the power if the kettle is switched on dry, and a second bimetal disc in the steam trips an over-centre lever that cuts it when the water boils.
In his kettle (Fig. 14) the steam leaves through a hole high in the wall and runs down a passage between the handle and the wall to the control. A knob resets it.
Source: J. C. Taylor, US Patent 4,358,666 (filed 1980, granted 1982). Picture: its Fig. 14.
Lanjutan
Unknown
Arahan
1
1
Read Taylor
Read Taylor
"The effect is that when the water boils, the lever 16 is tripped by the actuator 22 from its first to its second position, thus interrupting the supply of electricity to the heating element."
2
2
Fit the immersion heater
Fit the immersion heater
Make the kettle body with a spout, lid and handle, an opening low in the back wall for the heater head and a hole high in the wall under the handle for steam. Fix the immersion heater's head watertight in the low opening, with its element low in the kettle and its hot return brazed to the head so the head heats up if the element runs dry. Form a steam passage between the handle and the wall from the high hole down to the head. Body material, size and heater rating are not given.
Bahan untuk langkah ini:
Logam tidak diketahui1 kettle body
Unsur pemanas1 immersion heaterAlatan diperlukan:
Penyuluh pateri keras
Gerudi Tiang
Set Mata Gerudi
Kaedah pembentukan tidak diketahui
Dimensi tidak diketahui3
3
Build the switch-on-dry unit
Build the switch-on-dry unit
On the head mount a switch unit with three pins (line, neutral and earth) for the kettle lead's socket. Wire the line pin to one cold end of the element through a movable contact on a springy conductive strip and a fixed contact. Rivet the tongue of a snap-acting bimetal disc to a pillar so its body touches the head. Fit a sliding link that the disc pushes: at about 120 °C (Taylor: "say 120° C.") the disc snaps over and the link parts the contacts.
Bahan untuk langkah ini:
Bahan penebat tidak diketahui1 switch unit bodyLogam tidak diketahui1 pins, contacts and strip
Jalur dwilogam1 dry-switch discAlatan diperlukan:
Gerudi TiangSet Mata Gerudi4
4
Make the steam unit
Make the steam unit
Press a disc of sheet bimetal into a domed die, with a cut-out that leaves a tongue in the middle, so it snaps over when steam heats it. Mount it by its rim on a lever that rocks on two knife edges in notches of a body seated over the switch unit, held by two over-centre C-springs, with a shroud round the pins and a steam opening sealed by an O-ring. A finger of the lever passes through the sliding link; a knob on the lever comes out through the housing. The trip temperature and bimetal grade are not given.
Bahan untuk langkah ini:
Jalur dwilogam1 steam discBahan penebat tidak diketahui1 steam unit body and lever
Spring2 C-springs
O-ring1 kepingAlatan diperlukan:
Kaedah pembentukan tidak diketahui5
5
Close up and use
Close up and use
Screw the outer housing over both units into the threaded pillars, the knob through its opening and the steam passage meeting the steam unit's channel. Fill, plug in the lead and press the knob down to close the contacts. When the water boils, steam reaches the disc, the lever snaps over and the power goes off; switched on dry, the head heats and the other disc cuts it and holds the lever off. Press the knob to reset.
Bahan untuk langkah ini:
Bahan penebat tidak diketahui1 outer housing
Kord fleksibel berpalam1 kettle lead with socketBahan
7- 1 pins, contacts and stripPemegang Tempat
- 1 immersion heaterPemegang Tempat
- 1 outer housingPemegang Tempat
- 1 steam discPemegang Tempat
- 2 C-springsPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kettle lead with socketPemegang Tempat
Alatan Diperlukan
5- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.