SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Dicipta oleh

Penny

14. Oktober 2026DK
20
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Pertengahan
Two to three days

Arahan

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Bahan untuk langkah ini:

Bar keluli alat leperBar keluli alat leper1 keping

Alatan diperlukan:

Kikir LogamKikir Logam
Gerimit tanganGerimit tangan
Angkup Digital 6 InciAngkup Digital 6 Inci
Relau tukang besiRelau tukang besi
Baldi pelindapkejutanBaldi pelindapkejutan
Cermin mata keselamatanCermin mata keselamatan
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Bahan untuk langkah ini:

Jalur kayu kerasJalur kayu keras2 keping
Bar Bulat Keluli LembutBar Bulat Keluli Lembut0.3 m

Alatan diperlukan:

Kikir LogamKikir Logam
Relau tukang besiRelau tukang besi
Baldi pelindapkejutanBaldi pelindapkejutan
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Bahan untuk langkah ini:

Kepingan LoyangKepingan Loyang1 keping
Benang linen berlilinBenang linen berlilin3 m

Alatan diperlukan:

Gunting kepingan logamGunting kepingan logam
Gerimit tanganGerimit tangan
Kikir LogamKikir Logam
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Alatan diperlukan:

Kikir LogamKikir Logam
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Bahan untuk langkah ini:

Jongkong loyangJongkong loyang2 kg
ArangArang1 as required
Pasir tuanganPasir tuangan5 kg

Alatan diperlukan:

Relau tukang besiRelau tukang besi
Mangkuk Pijar Tanah Liat Tahan ApiMangkuk Pijar Tanah Liat Tahan Api
Penyepit Mangkuk PijarPenyepit Mangkuk Pijar
Kekotak acuan pasir (atas dan bawah)Kekotak acuan pasir (atas dan bawah)
Sarung tangan kimpalanSarung tangan kimpalan
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Bahan untuk langkah ini:

AirAir1 liter

Alatan diperlukan:

Silinder penyukatSilinder penyukat
Kikir LogamKikir Logam
7

A binary set of weights

Memuatkan buku nota Jupyterโ€ฆ
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Bahan

9

Alatan Diperlukan

12

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...