Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Flat Harvesting Basket: the Willow 3-Peck Fruit Flat (Hasluck, 1903)
Woody

Dicipta oleh

Woody

4. November 2026NO
3
0
0
1
0

Flat Harvesting Basket: the Willow 3-Peck Fruit Flat (Hasluck, 1903)

The basket-maker's 'flat' for the fruit season: an oblong willow basket with a woven stick bottom about 19 1/2 in wide, straight sides 8 in high, a rope handle at each end and its own flat lid on a bent bow. Rough brown osiers do for the bottom; eight white ones start the sides. Source: Paul N. Hasluck, Basket Work of All Kinds (1903), pp. 64-69. Picture: Fig. 65 of the book.
Lanjutan
Unknown

Arahan

1

Soak the osiers and weave the bottom

Soak the osiers until pliable. Cut eight sticks about 17 in long; set the two thickest in the screw-block 19 1/2 in apart outside, the rest between, and weave the bottom with the roughest osiers as for Hasluck's square basket. Take it out and trim it with the picking knife.

Bahan untuk langkah ini:

Ranting willow yang lebih tebalRanting willow yang lebih tebal8 17 in
Ranting willowRanting willow1 weavers

Alatan diperlukan:

AirAir
Gunting pemangkas satu tanganGunting pemangkas satu tangan
Papan Kayu RataPapan Kayu Rata
2

Stake up

Drive nine stakes into the weaving beside the sticks along each side, and seven through the sticks at each end after opening holes with the bodkin, the eight thickest at the corners. Prick them up and gather them in a hoop.

Bahan untuk langkah ini:

Pancang dedaluPancang dedalu32 9 per side, 7 per end

Alatan diperlukan:

Jarum penyerap taliJarum penyerap tali
Gunting pemangkas satu tanganGunting pemangkas satu tangan
3

Upset the sides

Point eight white osiers. With no foot rim, start by driving four in beside the first stakes at the left of one 19 1/2 in side. Sitting high with the work between your knees, upset with four rods pulled tight into the bend of each stake, each in front of three stakes, behind the fourth and out (Fig. 65). Start the other four at the opposite corner, finish the tops round the corners, then add one more round with three rods.

Bahan untuk langkah ini:

Ranting willowRanting willow8 white, upsetting

Alatan diperlukan:

Gunting pemangkas satu tanganGunting pemangkas satu tangan
Jarum penyerap taliJarum penyerap tali
TukulTukul
4

Weave and add handles

Weave with rods in their lengths, each butt behind the next stake, left to right, until the sides are 8 in high all round outside. For each end handle push a stiff rod down beside the third stake, twist it rope-like, push its top through about 1 1/2 in below the top by the fifth stake, leave a bow, and twist it over the bow three times (Fig. 66).

Bahan untuk langkah ini:

Ranting willowRanting willow1 weaving
Ranting willowRanting willow2 handles

Alatan diperlukan:

TukulTukul
Jarum penyerap taliJarum penyerap tali
5

Pair off and border

Pair off a round with two rods from the back. Make the border by laying down stakes and working them round the corners (Fig. 67), finish by cramming, and trim inside and out.

Bahan untuk langkah ini:

Ranting willowRanting willow2 pairing

Alatan diperlukan:

Gunting besarGunting besar
Gunting pemangkas satu tanganGunting pemangkas satu tangan
6

Make the lid

Notch a bow stick at the corners, bend it to the basket's shape and tie a strainer across to hold the width. Bind in two thick split sticks a little longer than the flat, flat side inward, on four scallom rods lapped round the bow (Figs. 68-69), and weave the lid between them.

Bahan untuk langkah ini:

Ranting willow yang lebih tebalRanting willow yang lebih tebal3 bow, two lid sticks
Ranting willowRanting willow1 scalloms, weavers

Alatan diperlukan:

Gunting pemangkas satu tanganGunting pemangkas satu tangan
TukulTukul

Bahan

3

Alatan Diperlukan

6

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...