SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Mild Steel Bar Stock Forged from an Ingot
Mills roll steel ingots into bar between grooved rolls. Before rolling mills, and in any forge today, the same shapes are drawn out by hand: cut a billet from a low-carbon (mild) steel ingot, heat it, and hammer it longer and thinner, square first; then eight-sided and round in a swage block for round bar and rod, or flattened for flat bar.
Hand-forged bar is not as exact as rolled bar: measure it and allow for that. Mild steel does not harden when cooled in air, so the bar is left to cool on its own.
Lanjutan
A day per few metres
Arahan
1
1
Where the ingot comes from
Where the ingot comes from
The ingot must be low-carbon (mild) steel.
2
2
Light the forge
Light the forge
Build a deep, clean charcoal fire in the forge with the air on.
Bahan untuk langkah ini:
Arang10 kgAlatan diperlukan:
Relau tukang besi3
3
Cut billets
Cut billets
Heat the ingot to a yellow heat and cut billets from it on the hot-cut hardy, striking with the sledgehammer. Wear apron, gloves, glasses and ear protection.
Bahan untuk langkah ini:
Jongkong keluli5 kgAlatan diperlukan:
Pahat potong andas
Tukul besar
Penyepit tukang besi
Andas
Apron Kulit
Sarung tangan kimpalan
Cermin mata keselamatan
Penutup telinga pelindung4
4
Draw out square
Draw out square
Heat a billet to yellow. Hammer it on the anvil face, a quarter turn after every few blows, so it stays square as it lengthens. Return it to the fire when it cools to red; never let it spark white.
Alatan diperlukan:
Tukul tukang besiPenyepit tukang besiAndasRelau tukang besi5
5
Square bar
Square bar
For square bar, stop at the size you need and true the faces under the flatter.
Alatan diperlukan:
Perata tempaanTukul besar
Angkup Digital 6 Inci6
6
Round bar and rod
Round bar and rod
For round, knock the square's corners down to eight sides, then turn it in the swage block's round groove under the hammer until round. Smaller grooves give rod.
Alatan diperlukan:
Blok acuan berlubangTukul tukang besiAngkup Digital 6 Inci7
7
Flat bar
Flat bar
For flat bar, draw the square wider and thinner on its edge and face, then smooth it with the flatter.
Alatan diperlukan:
Fuller (besi pembuat lurah)Perata tempaanTukul besarAngkup Digital 6 Inci8
8
Straighten and cool
Straighten and cool
At a low red heat, sight along the bar and tap it straight on the anvil. Lay it on the floor to cool in still air.
Alatan diperlukan:
Tukul tukang besi
Pembaris lurus9
9
Clean and measure
Clean and measure
Wire-brush off the scale, cut to length, and record each bar's size and length.
Alatan diperlukan:
Set berus dawaiAngkup Digital 6 Inci
Pita Ukur10
10
Troubleshooting
Troubleshooting
Drawing out troubleshooting.
Flow
Loading...
Alatan Diperlukan
17- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- 1 vendor sell this, none ship to you yetPemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.