Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)
Ear muffs that seal well and still stop low-pitched noise. Each ear is covered by a rigid cup on a cushion made of a thin PVC tube, emptied of air and part-filled with liquid. Pressed on, the liquid flows round the whole rim and fits the cushion to the head, yet cannot compress, so the cup does not vibrate as a whole and pass the sound in. A sprung headband with a pad holds the cups on ball joints.
Result: circumaural ear defenders effective against low-frequency noise.
Source: E. A. G. Shaw and G. J. Thiessen (National Research Council of Canada), US 2,801,423 (1957). Unknown: sizes and the attenuation achieved. Picture: the patent drawing.
Pertengahan
Unknown
Arahan
1
1
Make the cups
Make the cups
Make two rigid, non-porous cups to go over the ears, of wood, a hard plastic or a light metal such as aluminium. Widen each rim to about the width of the cushion, and make a small hole in the rim for the cushion's filling nipple. Fix a ball joint on the back of each cup. Not given: sizes.
Bahan untuk langkah ini:
Bahan tidak diketahui2 cawan
Logam tidak diketahui2 ball jointsAlatan diperlukan:
Mesin Pelarik Logam
Dimensi tidak diketahui2
2
Make the liquid cushions
Make the liquid cushions
For each cup make an endless tube of thin, pliable but non-stretching plasticised PVC, 0.005 to 0.01 in thick, with a filling nipple. Draw out almost all the air, then fill it with liquid to more than a quarter but well under the whole of its cross-section: enough to reach right round the rim when pressed, not so much that it cannot seal. Fix it on the rim with the nipple in the hole. Ours: water as the liquid. Not given: tube size.
Bahan untuk langkah ini:
Kepingan PVC1 thin plasticised PVC tube
Air1 fillingAlatan diperlukan:
Set picagari3
3
Fit the headband and wear them
Fit the headband and wear them
Make a resilient headband frame with a sponge-rubber pad at its middle and a wire loop at each end. Through each loop pass a threaded stub from the cup's ball joint, with a washer, and tighten with a wing nut. Put the cups over the ears: the cushions take the shape of the head and seal, while the cups stay still against the low-frequency sound. Ours: spring steel for the frame.
Bahan untuk langkah ini:
Dawai keluli spring1 frame and loopsBahan tidak diketahui1 sponge rubber padLogam tidak diketahui2 threaded stubs
Sesendal Rata2 keping
Nat sayap2 kepingAlatan diperlukan:
Playar hujung bulatBahan
7- 1 sponge rubber padPemegang Tempat
- 2 threaded stubsPemegang Tempat
- 1 thin plasticised PVC tubePemegang Tempat
- 1 fillingPemegang Tempat
- 1 frame and loopsPemegang Tempat
- 2 kepingPemegang Tempat
- 2 kepingPemegang Tempat
Alatan Diperlukan
4- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Bahan Blueprint Bersambung
Blueprint ini membuat
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.