Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Iron Ball Mill: Grüson Drum with a Stepped Die Ring and Two Screens (Richards, 1903)
The Grüson ball mill: a drum turning on a horizontal axis, charged with chilled iron or steel balls of mixed sizes. The balls grind the ore against each other and against a stepped die ring. The ground ore passes out through a coarse and a fine screen; the oversize is carried back in.
Result: a mill for fine grinding of cement, fertiliser, clay and soft ores, wet or dry. Sizes from 0.66 m to 1.83 m across.
Source: R. H. Richards, Ore Dressing, vol. I (1903), § 225, Figs. 172a-b and Table 149. Unknown: dimensions beyond the table, and the materials of the side plates, screens and shaft. Picture: Richards, Figs. 172a-b.
Lanjutan
Unknown
Arahan
1
1
Make the drum and the die ring
Make the drum and the die ring
The drum is two side plates (b) joined round the edge by the die ring (a). The die ring is five perforated, spiral plates of chilled iron. Each plate laps the next, so they form steps: the balls drop from one step to the next, and the space under each step lets the oversize from the screens back in. Not given: the side-plate material, sizes, hole sizes.
Bahan untuk langkah ini:
Tuangan besi5 die plates, chilled iron
Bahan tidak diketahui2 side platesAlatan diperlukan:
Dimensi tidak diketahui
Sepana boleh laras2
2
Put the two screens round it
Put the two screens round it
Outside the die ring, fit a coarse perforated screen (c) to take the wear. It is in five parts with spaces between them and has back-deflecting holes (g). Outside that, fit a fine gauze screen (d). At the end of each section of fine screen, fix a deflector or shovel (f). As the drum turns, it carries the oversize up and back into the grinding space. Not given: the screens' metal and mesh.
Bahan untuk langkah ini:
Plat ayak berlubang1 coarse screen, 5 parts
Kain ayak dawai tenunan1 fine screenBahan tidak diketahui5 deflectorsAlatan diperlukan:
Dimensi tidak diketahuiSepana boleh laras3
3
Mount and house it
Mount and house it
Carry the drum on a horizontal shaft in two bearings; the figures show them on masonry piers. Enclose the drum in a plate iron housing with a discharge spout (e) below, a feed hopper (h) at one end, a manhole (i) and a dust pipe (k) on top. Ours: steel sheet for the plate iron.
Bahan untuk langkah ini:
Aci keluli1 mill shaft
Blok galas2 keping
Kepingan Keluli Lembut1 housing, spout, hopperAlatan diperlukan:
Sepana boleh larasDimensi tidak diketahui4
4
Fit the drive
Fit the drive
Drive the mill by gear and pinion. In the figure, the gear is on the mill shaft and the pinion on a countershaft that carries tight and loose pulleys. A belt from the line shaft runs on the pulleys: on the tight pulley the mill turns, on the loose pulley it stops.
Bahan untuk langkah ini:
Roda gear besar1 on the mill shaft
Pinion1 kepingAci keluli1 countershaftBlok galas2 keping
Takal tetap dan takal bebas1 kepingAlatan diperlukan:
Tali sawat pemacuSepana boleh laras5
5
Charge the balls (size sets the charge)
Charge the balls (size sets the charge)
Load chilled iron or steel balls in mixed sizes; mixed sizes grind better than one size. Size is the variable: No. 0 (0.660 m drum, 45 rev/min) takes 15 kg of 40 mm and 45 kg of 80 mm balls, 60 kg in all. No. 2 (1.330 m, 30 rev/min) takes 100 kg each of 100, 115 and 125 mm, 300 kg. No. 4 (1.830 m, 25 rev/min) takes 217 kg each of the same three sizes, 650 kg. The bigger the drum, the slower it turns and the heavier its charge.
Bahan untuk langkah ini:
Media pengisar (bebola keluli)300 kg for No. 2; 60 kg No. 0, 650 kg No. 4Alatan diperlukan:
Penimbang pelantar industri6
6
Grind
Grind
Feed the ore, egg-size, through the hopper and run the mill wet or dry. Power, and output per 24 hours: No. 0 takes 1/4 horse power and grinds 1,680 kg of copper ore to 15 mesh, or 840 kg of chrome iron ore to 130 mesh. No. 2 takes 2 1/2 to 3 horse power: 14,400 kg of brick bats to 20 mesh, or 1,920 kg of emery to 200 mesh. No. 4 takes 9 to 11 horse power: 12,720 kg of gold ores to 40 mesh, or 10,800 kg of chrome iron ore to 130 mesh. Wear: 1,345 kg of balls for 102,400 barrels of cement, about 0.139 lb a ton. The end plates last 18 months. Hard quartz ores wear the balls too much.
Alatan diperlukan:
Tali sawat pemacu
AirBahan
11- 5 die plates, chilled ironPemegang Tempat
- 5 deflectorsPemegang Tempat
- 1 coarse screen, 5 partsPemegang Tempat
- 1 fine screenPemegang Tempat
- 1 countershaftPemegang Tempat
- 2 kepingPemegang Tempat
- 1 housing, spout, hopperPemegang Tempat
- 1 on the mill shaftPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 300 kg for No. 2; 60 kg No. 0, 650 kg No. 4Pemegang Tempat
Bahan Blueprint Bersambung
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.