Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Jigsaw: Motor-Rocked C-Frame on a Leaf Spring (Heese, US 2,692,622, 1954)
A small electric jig saw for curved cuts. A long U-shaped frame holds a fine blade stretched between its two arms. The frame's back end hangs on an L-shaped leaf spring, and an eccentric on a motor shaft rocks its lower arm up and down, so the blade saws through a slot in the table while the spring flexes. A wing nut tensions the blade; sawdust falls into a box below.
Result: a compact motor-driven jig (scroll) saw.
Source: G. O. Heese, US 2,692,622 (1954). Unknown: materials, sizes, the motor and the stroke. Picture: the patent drawing.
Pertengahan
Unknown
Arahan
1
1
Build the base and table
Build the base and table
Make a long flat base, wider at the front. Fasten a long upright support along it, its back end a separate upright strip. Across the wide front stand two walls with matching upright guide slots, carrying a level table that overhangs to the front with a slot for the blade. Under the overhang set a removable open box for sawdust. Not given: materials, sizes.
Bahan untuk langkah ini:
Bahan tidak diketahui1 base, support, walls, table, box
Pelbagai bolt heksagon1 fastenersAlatan diperlukan:
Gergaji Besi
Gerimit tangan
Dimensi tidak diketahui2
2
Make the C-frame and spring hinge
Make the C-frame and spring hinge
Make a U-shaped blade frame: an upper arm, a lower arm, and a back piece made in one with the lower arm and bolted to the upper. Fix the upright part of an L-shaped leaf spring to the support's back strip; its flat part goes into a slot in the frame's back piece and is held by the same bolt. The frame can now swing up and down on the spring, its lower arm running in the walls' guide slots under the table.
Bahan untuk langkah ini:
Logam tidak diketahui1 frame arms and back
Spring daun1 kepingPelbagai bolt heksagon1 keping
Nat Heksagon1 kepingAlatan diperlukan:
Sepana boleh laras3
3
Fit the motor and eccentric
Fit the motor and eccentric
Fix an electric motor on the wide front of the base with its shaft running across under the frame's lower arm. Put two bolts down through the lower arm, one each side of the shaft; on them hang a lower strip resting on nuts and an upper strip under the arm, with a coil spring on each bolt pushing the strips apart. Fix an eccentric on the motor shaft between the two strips: as it turns it rocks the frame. Not given: the motor, the throw.
Bahan untuk langkah ini:
Motor elektrik1 keping
Sesendal sipi1 eccentricLogam tidak diketahui1 two stripsPelbagai bolt heksagon1 two boltsNat Heksagon2 keping
Set Spring Mampatan1 two coil springsAlatan diperlukan:
Sepana boleh laras4
4
Fit the blade clamps and use it
Fit the blade clamps and use it
On the lower arm fix a strip with a forked end that hooks under the blade's lower pin. On the upper arm fit a bracket with a cross pin; an arm rocks on it, its forked front end over the blade's upper pin, its back end pulled down by a bolt with a wing nut. Add forked guide strips above and below the table. To fit a blade, loosen the wing nut, hook both pins and tighten the nut to stretch the blade straight. Switch on and feed the work across the table. Ours: a pinned coping-saw blade.
Bahan untuk langkah ini:
Logam tidak diketahui1 clamp strips, bracket, arm, guides
Nat sayap1 kepingPelbagai bolt heksagon1 keping
Bilah gergaji lengkung1 pinned bladeAlatan diperlukan:
Sepana boleh larasBahan
10- 1 base, support, walls, table, boxPemegang Tempat
- 1 two boltsPemegang Tempat
- 1 clamp strips, bracket, arm, guidesPemegang Tempat
- 1 kepingPemegang Tempat
- 3 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 eccentricPemegang Tempat
- 1 two coil springsPemegang Tempat
- 1 kepingPemegang Tempat
- 1 pinned bladePemegang Tempat
Alatan Diperlukan
4- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Bahan Blueprint Bersambung
Blueprint ini membuat
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.