SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
WEARABLES
Coconut Fiber Harvesting — From Husk to Fiber
English
NongMali

Dicipta oleh

NongMali

22. April 2026TH
32
0
0
0
0

Coconut Fiber Harvesting — From Husk to Fiber

A guide to the traditional Thai methods of harvesting and extracting fibers from coconut husks (coconut fiber/coco fiber). Covering the selection of suitable coconuts, water retting, fiber separation by beating, through to sun drying and storage. Coconut fiber is a raw material for making rope, mats, brushes, and filter materials.

Pemula
2-4 weeks (including retting)

Arahan

1

Select suitable coconuts

Select mature coconuts (10-12 months old) with the outer shell turned brown. Mature coconuts have stronger and longer fibers than young coconuts. Young coconuts (green color) have fibers that are too soft for making rope.

Bahan untuk langkah ini:

Mature Coconuts (10-12 months)Mature Coconuts (10-12 months)20 keping
2

Peel off the outer shell from the coconut

Insert a sharp steel spike (crowbar) into the ground at an angle. Apply pressure with the force of the coconut on the tip of the steel to pierce into the shell, then pry it out. Repeat around the coconut until the shell comes off completely. Separate the shell (husk) from the coconut.

Alatan diperlukan:

Husking Spike (Iron Stake)Husking Spike (Iron Stake)
Work Gloves (Leather)
3

Cut the shell into small pieces

Cut the coconut shell into pieces approximately 15-20 cm in size. Smaller pieces will be soaked more thoroughly and the fibers will separate more easily

Alatan diperlukan:

MacheteMachete
4

Prepare the soaking basin

Prepare a soaking basin — this can be a large plastic tank, a cement pond, or a natural water pool. The water must be deep enough to fully submerge all the coconut husks. Still freshwater (not fast-flowing) gives the best results.

Bahan untuk langkah ini:

Water for Retting200 liter

Alatan diperlukan:

Large Plastic Tank or Concrete BasinLarge Plastic Tank or Concrete Basin
5

Soak the coconut husks in water (retting)

Submerge the coconut husk pieces in water and weigh them down with stones or wood to prevent floating. The water will gradually decompose the soft tissue (pectin) that holds the fibers together. This process is called retting.

Bahan untuk langkah ini:

Weighing StonesWeighing Stones5 kilogram
6

Check weekly

Check the husks every 7 days. Try pulling the fibers apart with your fingers. If the fibers are still difficult to separate, continue soaking. The water will turn dark brown and develop an odor — this is normal, resulting from microbial decomposition.
7

Soak for 2-4 weeks

Soaking duration depends on temperature: hot weather (30 degrees C and above) takes 2-3 weeks, cooler weather (20 degrees C) may take 4-6 weeks. When the fibers separate easily with your fingers, they are ready. Do not soak for too long — the fibers will become weak and brittle.
8

Lift the shells out of the water

Remove the soaked shells from the pond, let the water drip out for a moment, put them in a mesh bag or place them on a rack to drain. The remaining water in the pond is rich in nutrients — can be used to water plants

Alatan diperlukan:

Mesh Draining BagMesh Draining Bag
9

Beat to separate the fibers

Place the soaked husks on a hard surface (wooden board or stone). Use a wooden club to beat them gently and repeatedly to separate the fibers from the remaining soft tissue. Beat all over the piece, flip it and beat the other side.

Alatan diperlukan:

Wooden Beating MalletWooden Beating Mallet
Flat Wooden BoardFlat Wooden Board
10

Wash the fibers in clean water

Take the separated fibers and wash them in clean water. Knead and squeeze gently to wash out residual tissue, mud, and odor. Change the water 2-3 times until the rinse water is fairly clear.

Bahan untuk langkah ini:

Distilled Water (1 Liter)Distilled Water (1 Liter)40 liter

Alatan diperlukan:

Washing BasinWashing Basin
11

Sort fibers by length

Sort the fibers into 3 groups: long (15 cm and above) for making rope and weaving mats, medium (5-15 cm) for making brushes and padding, and short (below 5 cm) for mixing into potting soil or filter material.
12

Squeeze water from the fibers

Squeeze the fibers by hand as dry as possible, or use a press if available. The more water you squeeze out, the shorter the drying time will be.
13

Air dry the fibers

Spread thin fibers on a rack or canvas in direct sunlight. Flip every 3-4 hours for even drying. Takes 2-3 days in strong sunlight. Store in shade if it rains

Alatan diperlukan:

Drying RackDrying Rack
14

Check for dryness

Well-dried fibers feel completely dry, are not cool to the touch, and have a golden brown color. If still damp, they will have a musty smell and develop mold. Moisture content should be below 12%.
15

Comb the fibers to fluff them

Use a steel comb or your hands to comb the dried fibers apart so they become fluffy. Fibers that are clumped together are difficult to work with. Combing prepares the fibers for twisting into rope or weaving into mats.

Alatan diperlukan:

Steel Comb or Hand CardSteel Comb or Hand Card
16

Packaging and storage

Pack the dried fibers in jute sacks or breathable cloth bags. Do not use sealed plastic bags — moisture will cause mold. Store in a dry place, elevated off the ground. Dried coconut fiber can be stored for many years without deterioration in quality.

Bahan untuk langkah ini:

Burlap Storage SackBurlap Storage Sack3 keping

Bahan

5

Alatan Diperlukan

10

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...