Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Dicipta oleh

Forge

13. November 2026NO
6
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Pertengahan
8-15 minutes a pair, once practised

Arahan

1

Bar length and sizes

Memuatkan buku nota Jupyter…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Bahan untuk langkah ini:

Bar besi tempaBar besi tempa1 keping

Alatan diperlukan:

Pita UkurPita Ukur
PenselPensel
Helaian kertas tebalHelaian kertas tebal
Relau tukang besiRelau tukang besi
Pahat potong andasPahat potong andas
Penyepit Tukang BesiPenyepit Tukang Besi
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Alatan diperlukan:

Relau tukang besiRelau tukang besi
Andas paruhAndas paruh
AndurAndur
Tukul pembulatTukul pembulat
Penyepit Tukang BesiPenyepit Tukang Besi
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Alatan diperlukan:

Andas paruhAndas paruh
Tukul pembulatTukul pembulat
Penyepit Tukang BesiPenyepit Tukang Besi
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Alatan diperlukan:

Andas paruhAndas paruh
Fuller (besi pembuat lurah)Fuller (besi pembuat lurah)
AndurAndur
Tukul pembulatTukul pembulat
Penyepit Tukang BesiPenyepit Tukang Besi
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Alatan diperlukan:

Andas paruhAndas paruh
Penebuk panasPenebuk panas
Penebuk lubang ladamPenebuk lubang ladam
Tukul pembulatTukul pembulat
Penyepit Tukang BesiPenyepit Tukang Besi
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Alatan diperlukan:

Relau tukang besiRelau tukang besi
Andas paruhAndas paruh
Tukul pembulatTukul pembulat
Fuller (besi pembuat lurah)Fuller (besi pembuat lurah)
Penebuk panasPenebuk panas
Penebuk lubang ladamPenebuk lubang ladam
Penyepit Tukang BesiPenyepit Tukang Besi
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Bahan

1

Alatan Diperlukan

12

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...