Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Potentiometer: Podolsky Roller-Contact Unit in a Moulded Casing
Podolsky's variable resistor (Wirt Company, US 2,060,114, 1936). The carbon strip is bent into a ring inside a moulded casing, and instead of a sliding wiper a small roller runs round it. A coil spring presses the roller out against the strip with even pressure in every position, even over slight irregularities. The patent gives no sizes; the parts are named by what they do.
The picture: the patent's drawing (Figs. 8 and 9).
Pertengahan
2 hours
Arahan
1
1
Seat the strip in the casing
Seat the strip in the casing
Bend the resistance strip into a ring against the round inner wall of the moulded casing. A small rib across the wall stops both ends of the strip so it cannot shift; the thick part at the rib has a hole for bolting the casing to a panel. Ours: flat-nose pliers to ease the strip in.
Bahan untuk langkah ini:
Moulded Insulating Casing1 keping
Elemen Rintangan Karbon1 kepingAlatan diperlukan:
Playar Muncung Rata2
2
Bolt the terminals
Bolt the terminals
Put two terminal bolts through the casing wall, one at each end of the strip. Under each bolt head a small contact plate rests on the coated end of the strip.
Bahan untuk langkah ini:
Bolt Terminal2 keping
Contact Plate2 kepingAlatan diperlukan:
Playar muncung tirus3
3
Fit shaft, sleeve, collar and yoke
Fit shaft, sleeve, collar and yoke
The shaft turns in a sleeve fixed in the base of the casing. A collar on the shaft rests on the outer end of the sleeve; on the inner end the shaft carries a yoke, with a spring washer between yoke and sleeve so the shaft cannot slide. Ours: pliers to seat the spring washer.
Bahan untuk langkah ini:
Aci Kawalan1 keping
Shaft Sleeve1 keping
Shaft Collar1 keping
Shaft Yoke1 keping
Spring Washer1 kepingAlatan diperlukan:
Playar muncung tirus4
4
Fit the sprung roller
Fit the sprung roller
The yoke's slotted ends guide a flat stem. The roller sits in the stem's forked outer end. A washer on shoulders of the stem, pushed out by a coil spring, holds the roller on the strip with even pressure all the way round.
Bahan untuk langkah ini:
Roller Stem1 keping
Contact Roller1 keping
Sesendal Rata1 keping
Coil Spring1 kepingAlatan diperlukan:
Playar muncung tirusBahan
13- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 2 kepingPemegang Tempat
- 2 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
Alatan Diperlukan
2- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.