SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI

Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall
A. C. Stiles of South Bloomfield, Ohio, received US 3,764, dated 27 September 1844, for a rocking churn: an oblong box on rockers, split by a partition with holes, with a dasher on each side worked by arms on shafts across the ends, and one upright lever that rocks the box and works the dashers together.
This rung prints the partition, dashers and arms, builds the box and makes butter.
Lanjutan
About 6 hours, plus printing
Arahan
1
1
One lever, three motions
One lever, three motions
Memuatkan buku nota Jupyter…
2
2
Two dashers from one lever, before it
Two dashers from one lever, before it
Mitchell worked two dashers from one lever; Stiles adds rockers and a perforated partition between them.
3
3
Read US 3,764
Read US 3,764
"The machine is operated by moving the upright lever l, to and fro, which rocks the box, while at the same time it works the dashers up and down, thus throwing the cream through the partition d, till the butter is made."
4
4
Print the parts
Print the parts
Print the partition (/uploads/blueprints/rocking-twin-dasher-lever-churn-partition.stl), two dashers (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher.stl), two dasher arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher-arm.stl) and two lower arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-lower-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Bahan untuk langkah ini:
Filamen PETG1 kepingAlatan diperlukan:
Pencetak 3D filamen (FDM)5
5
Box on rockers
Box on rockers
Build a pine box about 260 × 120 × 150 mm with a close-fitting lid, sealed inside. Glue the partition across its middle and screw two curved pine rockers lengthwise underneath. Drill the lid for the two dasher handles.
Bahan untuk langkah ini:
Papan pain1 keping
Gam Kayu1 keping
Skru kayu #8 x 1"1 kepingAlatan diperlukan:
Gergaji Tangan
Gergaji Lengkung
Gerudi Tanpa Wayar
Set Mata Gerudi
Pengapit6
6
Shafts, arms and lever
Shafts, arms and lever
Set a 10 mm square shaft across each end on two studs, 60 mm above the lid. Fit a dasher arm on each, pointing inward and pinned to its dasher's handle, and a lower arm on each outside the box. Join the lower arms with a pine bar, and pivot an upright pine lever on a block near the box's foot, pinned to the bar's middle.
Bahan untuk langkah ini:
Pasak kayu keras1 keping
Papan pain1 keping
Bar Bulat Keluli Lembut1 keping
Skru mesin1 kepingAlatan diperlukan:
Gergaji Tangan
Gerudi Tanpa Wayar
Set Mata Gerudi
Set pemutar skru7
7
The patent drawing
The patent drawing
US 3,764 drawing sheet, public domain (expired patent).

8
8
Rock and churn
Rock and churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Work the lever to and fro: the box rocks and the dashers rise and fall in turn. Keep fingers clear of the arms and the rockers. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Bahan untuk langkah ini:
Krim pekat1500 ml
Garam Laut Kasar1 keping
Air1 kepingAlatan diperlukan:
Termometer prob kekal
Jam Randik
Penimbang Dapur Digital
Mangkuk adun keluli tahan karat (besar)9
9
Troubleshooting
Troubleshooting
Rocking twin-dasher churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**A. C. Stiles** of South Bloomfield, Pickaway County, Ohio, US 3,764, 27 September 1844. He claimed the combination of the rockers and dashers in the double-chambered churn. His drawing gives no sizes; ours are ours. FDM prints hold food in their layer lines, so wash well and replace when worn.
Bahan
11- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1500 mlPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
Alatan Diperlukan
11- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- 1 vendor sell this, none ship to you yetPemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.



