Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Rubber Squeeze Bulb: Latex Coagulated Inside a Split Mould Coated with Calcium Nitrate (Szegvari, Anode, US 1,949,502)
A seamless hollow rubber bulb grows inside a closed mould: the cavity is coated with a coagulant, the mould is filled with latex, and rubber sets on the walls until it is thick enough. The rest of the latex is poured out through the neck.
Result: a seamless rubber squeeze bulb with a neck; ours sized at about 60 ml.
Source: Szegvari, US 1,949,502 (American Anode, 1934); his example is a football bladder. Not given: times, strengths, vulcanising details. Picture drawn by Youblob.
Pertengahan
2 days
Arahan
1
1
Coat the mould cavity with calcium nitrate in acetone
Coat the mould cavity with calcium nitrate in acetone
Open the split mould and coat only the cavity with a solution of calcium nitrate in acetone, by brush or spray. The acetone evaporates and leaves a sticky film of coagulant. Ours: a cavity of about 60 ml with a neck.
Alatan diperlukan:
Kalsium nitrat
Aseton
Acuan bola dua belah
Berus cat lebar2
2
Close the mould under the latex
Close the mould under the latex
Lower both halves under the surface of latex and close them once they are submerged and the air bubbles are gone. Rubber now sets on the coated walls; the longer the contact, the thicker the wall.
Bahan untuk langkah ini:
Lateks getah asli1 as requiredAlatan diperlukan:
Periuk Besar3
3
Pour out the extra latex through the neck
Pour out the extra latex through the neck
Lift the mould out and turn it over so the liquid latex drains back through the neck. Refill with water holding a little acetic acid so the inner face sets too.
Alatan diperlukan:
Asid asetik (glasier)
Air4
4
Open under warm water and leach
Open under warm water and leach
Open the mould under running warm water, take out the bulb and leave it in the water until most of the soluble matter has leached out. Clean any liquid latex off with dilute ammonia.
Alatan diperlukan:
Air
Larutan ammonia cair5
5
Inflate lightly and dry
Inflate lightly and dry
Drain the bulb, inflate it lightly so it does not collapse, and dry it at room temperature or in a drying cabinet. The latex may hold sulphur and be vulcanised in the usual way; Szegvari gives no details.
Alatan diperlukan:
Ketuhar pengeringanBahan
1- 1 as requiredPemegang Tempat
Alatan Diperlukan
9- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.