Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Screwdriver: a Flat Blade Forged, Packed at a Low Heat and Tempered Grey (Holford, 1907)
A flat screwdriver is a steel shank flattened to a blade that fits the slot of a screw. H. Holford's 20th Century Toolsmith and Steelworker (1907) says most smiths make them so they twist or break on a hard screw, and gives his cure: forge it from 75-point carbon steel, strike the blade a few good blows on each flat at a low heat, harden it and let the temper run to grey.
His Fig. 60 shows the shape without its handle. He gives no sizes and no handle, which are unknown here; the brine bath is from his chapter on the hardening bath.
Source: H. Holford (1907), pp. 21, 118. Picture: his Fig. 60.
Pertengahan
Half a day
Arahan
1
1
Read Holford
Read Holford
"Strike it a few good blows on each flat side of the screw driving edge while at a low heat. Then harden and allow the temper to draw to a grey, cool off and you will have a screw driver that will give unlimited satisfaction."
2
2
Forge the shape
Forge the shape
Take good steel of 75 points carbon. Forge it to the shape of Fig. 60: a round shank, flattened at one end to the driving blade and drawn to a pointed tang at the other for the handle. Holford gives no sizes (unknown).
Bahan untuk langkah ini:
Bar keluli alat segi empat sama1 barAlatan diperlukan:
Relau Tempa
Andas
Tukul tukang besi
Penyepit tukang besi
Dimensi tidak diketahui
Cermin mata keselamatan
Sarung Tangan Tahan Haba3
3
Pack the blade
Pack the blade
At a low heat, strike a few good blows on each flat side of the driving edge.
Alatan diperlukan:
Tukul tukang besiAndasRelau TempaPenyepit tukang besi4
4
Harden and temper grey
Harden and temper grey
Heat the blade end evenly and quench it in the hardening bath. Holford's bath is clean water free from grease, best made into a brine with as much salt as the water will dissolve, kept as large and as cold as possible. Brighten the blade with a file so the colours show, draw the temper to a grey, then cool it off.
Alatan diperlukan:
Relau Tempa
Larutan garam tepuPenyepit tukang besi
Kikir halusSarung Tangan Tahan Haba5
5
Fit a handle
Fit a handle
Fit a handle on the tang. Holford shows the screwdriver without one and does not say what it is made of (unknown).
Bahan untuk langkah ini:
Bahan tidak diketahui1 handle6
6
History and honest limits
History and honest limits
Holford, a toolsmith writing for blacksmiths and tool dressers, says a good screwdriver is prized by every mechanic, woodworkers most of all, yet few smiths could make one that would not break or twist. His temper table lists the screwdriver at grey, in 0.75 carbon steel.
He gives no sizes, no handle and no heat for hardening; those are unknown here, and the tools are ours.
Bahan
2- Pemegang Tempat
- 1 handlePemegang Tempat
Alatan Diperlukan
9- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.