Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)
A separating funnel holds two liquids that do not mix, so the lower layer can be run off through a tap at the bottom. J. P. Demers (US 5,580,528, 1996) fuses a bought glass stopcock to the bottom of a pear-shaped glass vessel and screws a flexible plastic stem onto it, because the usual glass stem breaks just below the stopcock.
The glass stopcock body stays clear, so you can watch the boundary between the two liquids as it reaches the tap.
Source: J. P. Demers, US Patent 5,580,528 (filed 1995, granted 1996). Picture: its Figs. 1-3.
Lanjutan
Unknown
Arahan
1
1
Read Demers
Read Demers
"The stresses resulting from such impacts usually fracture the glass just below the stopcock, or else chip off the end of the stem ... When the fracture is close to the stopcock, repair is impossible without replacing the stopcock".
2
2
Blow the vessel
Blow the vessel
Blow a glass vessel, pear-shaped (or spherical or cylindrical), with a neck at the top for pouring in the liquids and an opening at the bottom. Glass, size and how it is blown are not given; the patent leaves this to a scientific glassblower.
Bahan untuk langkah ini:
Kaca tidak diketahui1 vesselAlatan diperlukan:
Penyuluh tiup kaca meja
Kaedah pembentukan tidak diketahui
Dimensi tidak diketahui3
3
Fuse on the stopcock
Fuse on the stopcock
Take a glass-bodied stopcock (bought: the patent calls them articles of commerce, with a glass or PTFE plug) and fuse its upper stem to the bottom of the vessel so the vessel opens straight into the stem. Form a male thread on the end of its lower stem (how is not given).
Bahan untuk langkah ini:
Pili kaca1 plug of glass or PTFEAlatan diperlukan:
Penyuluh tiup kaca mejaKaedah pembentukan tidak diketahui4
4
Make the plastic stem
Make the plastic stem
Make a stem of moderately flexible plastic tube with a female thread in its upper end and an inner shoulder where the end of the glass thread meets it. Lay an O-ring on the shoulder when the funnel will hold reactive or toxic liquids or work under pressure or vacuum. Cut the lower end at about 45 degrees as a drip tip. The plastic is not given.
Bahan untuk langkah ini:
Bahan tidak diketahui1 flexible plastic stem
O-ring1 kepingAlatan diperlukan:
Kaedah pembentukan tidak diketahuiDimensi tidak diketahui5
5
Assemble and use
Assemble and use
Screw the plastic stem onto the glass thread. Close the stopcock, pour the two liquids in at the neck, shake and let them separate, then turn the plug to line its bore up with the stems and run the lower layer off, watching the boundary through the glass stopcock. Unscrew the stem to clear a blocked stopcock.
Bahan
4- 1 vesselPemegang Tempat
- 1 plug of glass or PTFEPemegang Tempat
- 1 flexible plastic stemPemegang Tempat
- 1 kepingPemegang Tempat
Blueprint ini membuat
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.