SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Reading a Temperature Sensor — SIK Circuit 7
Ed

Dicipta oleh

Ed

17. Mac 2026FI
76
0
0
0
0

Reading a Temperature Sensor — SIK Circuit 7

Read temperature from a TMP36 sensor and display Celsius and Fahrenheit readings on the Serial Monitor. Your introduction to serial communication and real-world data.

Arahan

1

Parts & Introduction

The TMP36 is an analog temperature sensor that outputs a voltage proportional to temperature. You'll learn to use the Serial Monitor to display real-time readings — an essential debugging tool.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 1x TMP36 Temperature Sensor
  • 5x Jumper Wires

Warning: The TMP36 looks similar to the transistor. Look for "TMP" in tiny letters and a triangle logo. The transistor has "222" printed on it. Inserting the wrong component can damage it!

Bahan untuk langkah ini:

SparkFun Inventor's Kit - V3.2SparkFun Inventor's Kit - V3.21 kit

Alatan diperlukan:

Computer with Arduino IDEComputer with Arduino IDE
2

Hardware Hookup

Wiring Instructions

With the TMP36 flat side facing you and pins pointing down, the pins are (left to right): 5V, Signal, GND.

  1. Connect the left pin to 5V.
  2. Connect the middle pin (signal) to Analog Pin A0.
  3. Connect the right pin to GND.

That's it — just 3 wires! The TMP36 can only be connected in one direction. Double-check before powering on.

Bahan untuk langkah ini:

BreadboardBreadboard1 keping
Jumper WiresJumper Wires3 keping
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

temperature_sensor.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 07 — TEMPERATURE SENSOR

Use the serial monitor to read temperature from a TMP36 sensor.

Hardware connections:
  TMP36 (flat side, pins down, left to right): 5V, SIGNAL, GND
  Connect 5V pin to 5V, SIGNAL pin to analog pin 0, GND pin to GND.

This code is completely free for any use.
*/

const int temperaturePin = 0;

void setup()
{
  Serial.begin(9600);
}

void loop()
{
  float voltage, degreesC, degreesF;

  voltage = getVoltage(temperaturePin);

  degreesC = (voltage - 0.5) * 100.0;
  degreesF = degreesC * (9.0/5.0) + 32.0;

  Serial.print("voltage: ");
  Serial.print(voltage);
  Serial.print("  deg C: ");
  Serial.print(degreesC);
  Serial.print("  deg F: ");
  Serial.println(degreesF);

  delay(1000);
}

float getVoltage(int pin)
{
  return (analogRead(pin) * 0.004882814);
  // Converts 0-1023 to 0.0-5.0 volts
}

Bahan untuk langkah ini:

Arduino Uno R3Arduino Uno R31 keping

Alatan diperlukan:

Computer with Arduino IDEComputer with Arduino IDE
4

Test & Experiment

What You Should See

Open the Serial Monitor (magnifying glass icon in Arduino IDE, or Ctrl+Shift+M). You'll see lines updating once per second:

voltage: 0.73  deg C: 23.24  deg F: 73.84

Troubleshooting

  • Nothing happens: Open the Serial Monitor! The output goes there, not to the LEDs.
  • Gibberish text: Set the Serial Monitor baud rate dropdown to 9600.
  • Temperature unchanged: Pinch the sensor with your fingers to warm it up, or apply ice to cool it down.

Experiments to Try

  • Add an LED that turns on above a temperature threshold (like a heat warning).
  • Log data over time to see temperature trends.
  • Combine with the LCD (Circuit 15) to display temperature without a computer.

Bahan

5

Alatan Diperlukan

1
Jumlah anggaran
Apa yang dibeli oleh pembuatnya. Bahan tanpa harga diperoleh di tempat anda membelinya.
$107.45

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...