SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Forge

Dicipta oleh

Forge

18. Oktober 2026NO
6
0
0
0
0

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered

Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours. The picture: steel sewing needles (Wikimedia Commons).
Pertengahan
Half a day

Arahan

1

Cut, soften and straighten

Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.

Bahan untuk langkah ini:

Dawai pianoDawai piano70 mm

Alatan diperlukan:

Playar pemotong sisiPlayar pemotong sisi
Relau tukang besiRelau tukang besi
Playar muncung tirusPlayar muncung tirus
AndasAndas
2

Point

Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.

Alatan diperlukan:

Set KikirSet Kikir
Ragum BangkuRagum Bangku
Cermin mata keselamatanCermin mata keselamatan
3

Flatten and pierce the eye

Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.

Alatan diperlukan:

AndasAndas
Tukul kepala baji lintangTukul kepala baji lintang
Gerimit tanganGerimit tangan
Set KikirSet Kikir
Ragum BangkuRagum Bangku
Cermin mata keselamatanCermin mata keselamatan
4

Harden in oil

Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.

Alatan diperlukan:

Relau tukang besiRelau tukang besi
Playar muncung tirusPlayar muncung tirus
Tangki lindap kejut berminyakTangki lindap kejut berminyak
Cermin mata keselamatanCermin mata keselamatan
5

Temper

Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.

Alatan diperlukan:

Ketuhar rawatan habaKetuhar rawatan haba
Termogandingan dengan paparanTermogandingan dengan paparan
AndasAndas
Tukul kepala baji lintangTukul kepala baji lintang
6

Scour and polish

Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.

Alatan diperlukan:

Kain emeriKain emeri
Minyak zaitunMinyak zaitun
SabunSabun
Habuk gergajiHabuk gergaji
Tali kulit pengasahTali kulit pengasah
Set KikirSet Kikir

Bahan

1
  • Pemegang Tempat

Alatan Diperlukan

17

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...