Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Stone Carving Chisels: Mallet-Headed Plain and Tooth Chisels and Points for Soft Stone (Holford, 1907)
Soft stone such as limestone and sandstone is cut with chisels struck by a wooden mallet, so their heads are broad and a little rounded. H. Holford's 20th Century Toolsmith and Steelworker (1907) shows a set: plain chisels, tooth chisels with a row of sharp teeth, and points, forged from 3/4 inch octagon steel of 75 points carbon and tempered a very pale blue.
He gives no lengths, widths or tooth spacing; those are unknown here. The brine bath is from his chapter on the hardening bath.
Source: H. Holford (1907), pp. 21, 131-133, 140-141. Picture: his Fig. 71.
Pertengahan
A day for a set
Arahan
1
1
Read Holford
Read Holford
"In cutting soft stone of any description wooden mallets are used, consequently the heads of the tools are made broad and a little rounding, so as not to cut or bruise the mallet."
2
2
Forge the mallet heads
Forge the mallet heads
Use 3/4 inch octagon steel of 75 points carbon. For each tool, upset the head end a little, fuller it in, draw it out, then swage it to its broad, slightly rounded shape between top and bottom swages (Fig. 78). For a narrow chisel, forge the head first; for a wide one, forge the cutting end first. Sizes are not given (unknown).
Bahan untuk langkah ini:
Bar keluli alat segi lapan1 3/4 in octagonAlatan diperlukan:
Relau Tempa
Andas
Tukul tukang besi
Andur
Fuller (besi pembuat lurah)
Swej atas dan bawah
Penyepit tukang besi
Dimensi tidak diketahui
Cermin mata keselamatan
Sarung Tangan Tahan Haba3
3
Forge the chisels and points
Forge the chisels and points
For a wide chisel, upset the end to the width of the chisel before drawing it down to a thin cutting edge. Hammer the flat surfaces. Draw the points down to almost a square point (Fig. 72). For tooth chisels, punch the teeth into the edge in a punch machine after the flat surfaces have been hammered, then file each tooth to an extremely sharp point.
Alatan diperlukan:
Relau TempaAndasTukul tukang besiPenyepit tukang besi
Mesin penekan tebuk
Kikir halus4
4
Harden the chisels
Harden the chisels
Heat the cutting edge very evenly along its whole length and dip it at least one inch into the hardening bath (clean water, best as a strong brine, kept large and cold). Polish it bright by rubbing it across a board spread with fine clean sand near the forge, and draw the temper to a very pale blue, the right temper for all limestone tools.
Alatan diperlukan:
Relau Tempa
Larutan garam tepu
Papan
Pasir HalusPenyepit tukang besiSarung Tangan Tahan Haba5
5
Harden the points
Harden the points
Dip the points deep into the bath. Draw the temper so it shows at least 5/8 inch back from the point; if it runs so fast that only the very tip is tempered, the point bends and breaks easily.
Alatan diperlukan:
Relau TempaLarutan garam tepuPapanPasir HalusPenyepit tukang besiSarung Tangan Tahan Haba6
6
History and honest limits
History and honest limits
Holford sets the soft-stone tools apart from those for granite and marble: soft stone takes wooden mallets, hence the broad heads, and a very pale blue temper. The finest stone carvers' tools, struck only lightly, he hardens without drawing any temper at all.
He gives no lengths, widths or tooth spacing; the tools used to make them are ours.
Bahan
1- 1 3/4 in octagonPemegang Tempat
Alatan Diperlukan
15- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.