SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
The Button Corkscrew: A Helix That Grips and a Disc That Stops It
Youblob (drawn diagram, draw_corkscrew.py) · CC0
YourGrandma

Dicipta oleh

YourGrandma

27. September 2026IS
10
0
0
0
0

The Button Corkscrew: A Helix That Grips and a Disc That Stops It

A cork is squeezed into a bottle neck so hard that pulling it out by a simple worm takes a strong arm — and a worm driven too far pierces the cork and pushes crumbs into the wine. Samuel Henshall, an English clergyman, took out British patent No. 2061 on 24 August 1795 for a corkscrew with a button: a concave disc fixed between the worm and the shank. The button stops the worm once it is deep enough, and turning on past that point twists the whole cork in the neck, breaking its hold on the glass before it is pulled. Matthew Boulton's works in Birmingham made it. This rung works out the worm's turns and grip and the force a pull needs, and makes and tests a button corkscrew.
Pemula
About 2 hours

Arahan

1

Worm pitch, grip and pulling force

Memuatkan buku nota Jupyter…
2

The helix underneath it

A corkscrew worm is a helix with nothing inside it. The embedded blueprint shows the helix as a ramp wrapped round a cylinder.
3

Make a worm and a button

Wind 2 mm spring steel wire round a 6 mm rod held in a vice, five turns at an 8 mm pitch — set the pitch by winding over a spacer strip. Grind the free end to a point on the outside of the helix so it follows the helix, not the centre. Leave a straight tail as the shank. For the button, drill a 20 mm steel washer to fit the shank and file its underside slightly concave with abrasive paper wrapped round a rod. Slide it down to where the worm starts and solder it in place. Fit a wooden handle across the top of the shank.

Bahan untuk langkah ini:

Dawai keluli springDawai keluli spring1 keping
Sesendal RataSesendal Rata1 keping
Pasak kayu kerasPasak kayu keras1 keping
Pateri timah-plumbumPateri timah-plumbum1 keping

Alatan diperlukan:

Ragum BangkuRagum Bangku
Gerudi Tanpa WayarGerudi Tanpa Wayar
Set Mata GerudiSet Mata Gerudi
Pelbagai kertas pasirPelbagai kertas pasir
Alat pematerianAlat pematerian
Sarung Tangan Kerja KulitSarung Tangan Kerja Kulit
Cermin Mata Keselamatan JernihCermin Mata Keselamatan Jernih
4

Measure the pull, with and without the twist

Recork several empty wine bottles with new corks of the same kind, using a hand corker, and let them stand a day. On the first, drive the worm in until the button touches, stop, and pull straight up with a spring scale hooked to the handle: read the peak force. On the next, drive it in until the button touches, then turn two more turns so the cork rotates in the neck, and pull again. Compare the peak forces. Compare also with a commercial corkscrew.

Bahan untuk langkah ini:

Gabus penyumbatGabus penyumbat6 keping
Set penggabus botol wainSet penggabus botol wain1 keping
Pembuka GabusPembuka Gabus1 keping

Alatan diperlukan:

Meter Daya (Neraca Spring)Meter Daya (Neraca Spring)
5

A cork that will not come out cleanly

Cork removal problems.

Flow

Loading...
6

History and honest limits

**Samuel Henshall** was granted **British patent No. 2061** on 24 August 1795 — the first patent for a corkscrew. Matthew Boulton made Henshall's corkscrews at Soho, Birmingham, marked "Obstando Promoves". Later designs added threads, levers and wings to take the effort out of the pull. **Honest limits.** The cork pressure and friction in the notebook are illustrative; measure your own pulls. The patent itself is not in the patent databases used for this programme; its details here come from museum and patent-office sources.

Bahan

7

Alatan Diperlukan

8

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...