SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
The Grain Auger: Archimedes' Screw Spun Fast in a Tube
Martin

Dicipta oleh

Martin

27. September 2026NO
5
0
0
0
0

The Grain Auger: Archimedes' Screw Spun Fast in a Tube

Archimedes' screw lifts water slowly by trapping it between turns of a spiral. Close the spiral in a tight tube and spin it fast, and it moves dry grain instead: the flights push the grain along and the tube keeps it from turning with them. The auger fills bins, empties combine tanks and loads trucks, at any angle from flat to steep, with nothing but a shaft and a motor. It is a sibling of the bucket elevator: the elevator lifts straight up in buckets and needs a tower; the auger lifts at a slant in a single tube and goes where it is carried. This rung works out an auger's theoretical delivery and why its fill factor must be measured, and builds a clear-tube auger to measure it at three angles.
Pemula
About 4 hours

Arahan

1

Delivery, fill factor and power

Memuatkan buku nota Jupyter…
2

The water sibling

The same spiral lifts water when turned slowly in an open trough. The embedded blueprint builds one; compare how each holds its load.
3

Build a clear-tube auger

3D-print screw flights 40 mm across with a 40 mm pitch, in 150 mm sections with an 8 mm bore, and thread them onto an 8 mm threaded rod locked with nuts. Slide the screw into a clear acrylic tube with a 42 mm bore. Cut an intake window at the bottom and a discharge hole at the top. Mount the tube on a plywood stand that can be set at 0, 20 and 40 degrees, with the rod running in skateboard bearings at each end. Drive the top end from a geared DC motor on an adjustable supply. Keep your fingers, hair and sleeves clear of the intake window while it turns.

Bahan untuk langkah ini:

Tiub akrilik (jernih)Tiub akrilik (jernih)1 keping
Rod berbenangRod berbenang1 keping
Galas papan selajuGalas papan selaju2 keping
Kepingan papan lapisKepingan papan lapis1 keping
Motor DC bergearMotor DC bergear1 keping
Kacang lentil keringKacang lentil kering3 kilogram

Alatan diperlukan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
Filamen PETGFilamen PETG
Unit kuasa arus terusUnit kuasa arus terus
Gerudi Tanpa WayarGerudi Tanpa Wayar
Set Mata GerudiSet Mata Gerudi
Sepana boleh larasSepana boleh laras
ProtraktorProtraktor
Cermin Mata Keselamatan JernihCermin Mata Keselamatan Jernih
4

Measure the fill factor

Keep the intake window buried in a tray of lentils. At each angle and at two motor speeds, run for 30 seconds, catch the discharge, weigh it, and read the shaft speed with the tachometer. Work out the theoretical delivery from the notebook's formula using your flight diameter, rod diameter and pitch, and the lentils' bulk density (weigh a measured jug full). The fill factor is measured delivery divided by theoretical. Tabulate it: it is highest flat and falls as the tube is tipped up, because more lentils slip back over the flights.

Alatan diperlukan:

Takometer DigitalTakometer Digital
Jam RandikJam Randik
Penimbang Dapur DigitalPenimbang Dapur Digital
Jag penyukatJag penyukat
BaldiBaldi
5

An auger that is not moving the grain

Grain auger faults, from the first to check.

Flow

Loading...
6

Context and honest limits

The screw conveyor is old; the portable farm auger in a tube is the form that moves most grain on farms today, from combine unloading augers to bin-filling augers. **Honest limits.** The notebook's theoretical delivery assumes a full tube moving one pitch per turn — no auger does this, which is why the bench test measures the fill factor. An auger damages some grain by rubbing, more at high speed and with fragile crops. And the exposed intake is one of the most common causes of serious injury on farms: guards stay on.

Bahan

6

Alatan Diperlukan

13

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...