SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI

Heat Control: The Pan Is Not the Hob, and It Does Not Follow the Dial
Turning the dial down does not cool the pan. It slows the rate at which heat is added, and the pan then takes its own time to fall — which for cast iron can be several minutes.
That lag is why so much cooking goes wrong at exactly the moment somebody notices it going wrong. By the time the dial has been turned down the food has already had another minute of full heat.
The other half is what happens when cold food lands in a hot pan. The pan gives up its stored heat to the food and its temperature DROPS, sometimes below browning temperature entirely — and how far it drops depends on the mass of the pan, not on the hob.
Pertengahan
3 hours
Arahan
1
1
Preheat the pan, then judge it by a test not a timer
Preheat the pan, then judge it by a test not a timer
Heat the empty pan before anything goes in. A pan that starts cold is still heating while the food is cooking, so the food's early minutes happen at a temperature nobody chose.
Judge readiness by a test. A drop of water skittering across the surface in a ball rather than boiling off means the pan is well above 100 degrees — the Leidenfrost effect, and a reliable free thermometer. Oil that shimmers and flows like water is another.
An infrared thermometer settles it in a second if you have one, and it is worth doing once with your own pans just to learn what the tests correspond to. That is calibrating a judgement against an instrument, which is the measurement batch's habit applied to a kitchen.
Bahan untuk langkah ini:
Minyak zaitun dara tulen1 keping
Air1 kepingAlatan diperlukan:
Kuali besi tuang
Termometer Bacaan Serta-merta
Kuali leper2
2
What cold food does to a hot pan
What cold food does to a hot pan
Memuatkan buku nota Jupyter…
Bahan untuk langkah ini:
Daging lembu tanpa lemak1 kepingAlatan diperlukan:
Kuali besi tuang
Komputer Meja
Termometer Bacaan Serta-merta3
3
Every setting is a different job
Every setting is a different job
HIGH is for browning and for boiling. It is the only setting where the surface gets past 140 degrees quickly, and the only one that will keep a big pot of water boiling with pasta in it.
MEDIUM is for cooking things through — the setting where the inside has time to reach temperature before the outside is ruined. Most things people burn were cooked on high when they wanted medium.
LOW is for sweating onions without colour, for reductions, and for anything with dairy or egg in it that will split or scramble if it gets hot. A simmer is occasional bubbles, not a rolling boil, and holding it there is what the last two rungs of this batch are about.
Bahan untuk langkah ini:
Bawang besar1 keping
Minyak zaitun dara tulen1 kepingAlatan diperlukan:
Senduk
Kuali leper
Sudu Kacau Kayu4
4
Listen to the pan
Listen to the pan
A pan is an instrument you can hear. A loud, sharp, continuous sizzle means water is leaving fast and the surface is above 100 degrees — browning is happening. A quiet pan with a soft bubbling means liquid, and steaming.
Silence from a pan that was loud means either the food is done and dry, or it is burning. Both need attention immediately and they sound the same, so look.
Smell is the other channel, and it leads sound by about a minute: nutty and sweet is the Maillard reaction working; acrid and sharp is past it. A cook who is listening and smelling does not need a timer for most things, and that is a skill built by paying attention rather than by being told.
Bahan untuk langkah ini:
Daging lembu tanpa lemak1 kepingAlatan diperlukan:
Kuali leper
Penyepit dapur
Buku NotaBahan
4- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.


