SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed.
Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down.
This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Pertengahan
About 4 hours
Arahan
1
1
Sheet speed from the slot
Sheet speed from the slot
Memuatkan buku nota Jupyter…
2
2
Water through a brush's back before it
Water through a brush's back before it
The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3
3
Read US 840,604
Read US 840,604
"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4
4
Cut the slots
Cut the slots
On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.
Bahan untuk langkah ini:
Berus penyental1 kepingAlatan diperlukan:
Ragum Bangku
Gerudi Tanpa Wayar
Set Mata Gerudi
Gergaji Lengkung
Penanda Kekal
Pembaris5
5
Taper the slots
Taper the slots
Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.
Alatan diperlukan:
Set pahat kayu
Tukul
Angkup Digital 6 Inci
Pisau Kraf6
6
Make the manifold
Make the manifold
Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.
Bahan untuk langkah ini:
Tiub tembaga1 keping
Penyambung loyang1 kepingAlatan diperlukan:
Pemotong tiub
Kikir (Kikir Tangan)
Sepana boleh laras7
7
Seat the manifold
Seat the manifold
Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.
Bahan untuk langkah ini:
Kepingan getah1 keping
Kepingan aluminium1 keping
Skru kayu #8 x 1"1 kepingAlatan diperlukan:
Gunting kepingan logam
Set pemutar skru
Pisau Kraf8
8
Handle, valve and drip cup
Handle, valve and drip cup
Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.
Bahan untuk langkah ini:
Tiub tembaga1 keping
Injap bebola1 keping
Penyambung loyang1 keping
Pita pengedap bebenang PTFE1 keping
Tin1 kepingAlatan diperlukan:
Pemotong tiub
Sepana boleh laras
Gerudi Tanpa Wayar
Set Mata Gerudi9
9
The patent drawing
The patent drawing
US 840,604 drawing sheet, public domain (expired patent).

10
10
Full flow against throttled
Full flow against throttled
Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.

Bahan untuk langkah ini:
Air1 kepingAlatan diperlukan:
Jag penyukat
Jam Randik
Pembaris
Hos taman11
11
A sheet that sprays, sputters or leaks
A sheet that sprays, sputters or leaks
Sheet-of-water fountain brush troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised.
**Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.
Bahan
11- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 2 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
Alatan Diperlukan
18- Pemegang Tempat
- 1 vendor sell this, none ship to you yetPemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Hos taman10% komisenPemegang Tempat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.


