SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Twisted-Strip Egg Beater: Faces Beat and Edges Cut
A wire beater passes through the egg and leaves a wake without much froth.
James P. McLean and Philemon A. Morley of Brooklyn received US 28,760, dated 19 June 1860, for an egg beater of corrugated or twisted strips of tin turned inside a can by a large and a small cog gear set between the double heads of its lid: "by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof."
This rung works out how much of a twisted face pushes, then prints the gears and a cage of twisted strips, builds the lid drive on a can, and times a beating.
Pertengahan
About 4 hours, plus printing
Arahan
1
1
How a twisted face beats
How a twisted face beats
Memuatkan buku nota Jupyter…
2
2
A geared wire beater before it
A geared wire beater before it
The embedded blueprint beats with bent wires. McLean and Morley use twisted strips with faces and edges.
3
3
Read US 28,760
Read US 28,760
"The superiority of our arrangement of egg beaters over those that are in common use, is that by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof, hence the action is analogous to the motion produced by the hand and spoon, whereas an ordinary wire beater simply passes through the egg like the rudder of a boat, leaving a simple wake behind it without producing an immediate fomentation as is the case with our beater."
4
4
Print the gears and cage
Print the gears and cage
Print the 36-tooth gear (/uploads/blueprints/twisted-strip-egg-beater-gear-36.stl), the 12-tooth gear (/uploads/blueprints/twisted-strip-egg-beater-gear-12.stl) and the cage of four twisted strips (/uploads/blueprints/twisted-strip-egg-beater-cage.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Bahan untuk langkah ini:
Filamen PETG1 kepingAlatan diperlukan:
Pencetak 3D filamen (FDM)5
5
Make the double lid
Make the double lid
Cut two plywood disks to the can's mouth. Space them 20 mm apart on three M5 screws with nuts, and drill both for the crank shaft and the cage shaft 48 mm apart.
Bahan untuk langkah ini:
Kepingan papan lapis1 keping
Skru mesin1 keping
Nat Heksagon1 keping
Sesendal Rata1 kepingAlatan diperlukan:
Gergaji Lengkung
Gerudi Tanpa Wayar
Set Mata Gerudi
Sepana boleh laras
Angkup Digital 6 Inci6
6
Fit the shafts and gears
Fit the shafts and gears
Epoxy the large gear on a crank shaft of 5 mm rod with a bent handle, and the small gear on the cage shaft, both between the heads. Epoxy the cage on the cage shaft's lower end.
Bahan untuk langkah ini:
Bar Bulat Keluli Lembut1 keping
Epoksi dua komponen1 kepingAlatan diperlukan:
Gergaji Besi
Ragum Bangku
Playar Muncung Rata7
7
The patent drawing
The patent drawing
US 28,760 drawing sheet, public domain (expired patent).
8
8
Beat egg whites
Beat egg whites
Put two egg whites in the can, fit the lid, and crank about once a second; time to stiff peaks.
Bahan untuk langkah ini:
Tin1 keping
Telur2 kepingAlatan diperlukan:
Jam Randik9
9
Gears that skip, a cage that scrapes
Gears that skip, a cage that scrapes
Twisted-strip egg beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**James P. McLean** and **Philemon A. Morley** of Brooklyn, assignors to P. A. Morley, received US 28,760, dated 19 June 1860. Their Fig. 2, for bakers, puts the strips on a vertical water-tight cylinder turning round a stationary handle, driven by a hand wheel whose rubber band grips the cylinder's grater-like funnel top instead of cog wheels. They claimed the twisted beaters in combination with the cylinder.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed strips and plywood heads stand in for tin. Your times are the result.
Bahan
9- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 2 kepingPemegang Tempat
Alatan Diperlukan
10- Pemegang Tempat
- Pemegang Tempat
- 1 vendor sell this, none ship to you yetPemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.