Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)
The same pine bench with a harder top: 14 maple strips set on edge, glued and screwed together, with a back board, a tool rack and a wooden vise on an iron bench screw.
Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
Pertengahan
Unknown
Arahan
1
1
Make the two leg frames
Make the two leg frames
Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.
Bahan untuk langkah ini:
Kayu pain1 2 x 4 in: legs, crosspiecesAlatan diperlukan:
Gergaji Tangan
Pahat lubang tanggam
Tukul2
2
Brace them together
Brace them together
Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.
Bahan untuk langkah ini:
Kayu pain1 2 x 4 in: braces
Bolt kepala bulat leher segi empat4 3/8 x 6 inAlatan diperlukan:
Gergaji Tangan
Gerimit engkol dan mata
Sepana boleh laras3
3
Build up the maple top
Build up the maple top
Make the main top M of 14 maple strips 7/8 in thick, 2 in wide and 3 1/2 ft long, set on edge, each glued and screwed to the next, all with the grain one way so it planes smooth. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.
Bahan untuk langkah ini:
Bahan tidak diketahui14 maple strips 7/8 x 2 in x 3 1/2 ft
Gam Kayu1 keping
Papan pain1 back board
Skru kayu1 kepingAlatan diperlukan:
Gergaji Tangan
Ketam blok
Pemutar skru rata4
4
Add the tool rack
Add the tool rack
Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.
Bahan untuk langkah ini:
Papan pain2 7/8 in, 3 1/2 ft
Paku1 kepingAlatan diperlukan:
Gerimit engkol dan mataGergaji TanganTukul5
5
Fit the vise
Fit the vise
Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).
Bahan untuk langkah ini:
Kayu pain1 2 x 6 block, 2 x 4 pieces, guide rails
Skru bangku untuk ukiran kayu1 kepingBolt kepala bulat leher segi empat1 for L and PPaku1 kepingAlatan diperlukan:
Gergaji TanganPahat lubang tanggamGerimit engkol dan mataSepana boleh larasTukulBahan
8- 1 2 x 6 block, 2 x 4 pieces, guide railsPemegang Tempat
- 1 for L and PPemegang Tempat
- 14 maple strips 7/8 x 2 in x 3 1/2 ftPemegang Tempat
- 1 kepingPemegang Tempat
- 2 7/8 in, 3 1/2 ftPemegang Tempat
- 1 kepingPemegang Tempat
- 2 kepingPemegang Tempat
- 1 kepingPemegang Tempat
Blueprint ini membuat
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.