IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
PTFE Rod: a Plug Sintered in Boiling Retene Vapour (Brubaker & Hanford 1946)
The first example of du Pont's way to shape PTFE: press a small rod of powder cold, then heat it above 327 °C out of the mould. Here the heat comes from the vapour of boiling retene, which boils at 394 °C, so the temperature holds steady by itself. The plug comes out sintered into one tough piece.
Source: M. M. Brubaker and W. E. Hanford (du Pont), US 2,400,099 (1946), Example I. The pressure is the patent's usual range, as the example gives none. The mould, press and the vapour-bath set-up are ours. Picture drawn by Youblob.
Ilọsíwájú
1 day
Ìlànà
1
1
Press a plug from the powder
Press a plug from the powder
At room temperature, press small particles of PTFE in a mould into a plug 0.5 in across and 0.7 in long. The example gives no pressure; the patent's usual range is 100–3000 lb/sq in.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Erùpẹ̀ resini PTFE1 as required for the plugÀwọn irinṣẹ́ tí a nílò:
Àwòṣe ìtẹ̀mọ́lẹ̀
Ẹ̀rọ ìtẹ̀ háídírọ́líìkì
Ìdíwọ̀n2
2
Set up a retene vapour bath
Set up a retene vapour bath
Boil retene so its vapour fills the space round a glass tube. Ours: retene in a flask on a burner, a reflux condenser on top, and the tube standing in the vapour.
Àwọn irinṣẹ́ tí a nílò:
Retene
Ìgò Gíláàsì Ìsàn
Kọ́ndẹ́nsà Ìpadàbọ̀
Ọ̀gọ̀ Bunsen
Àwọn tube ìdánwò3
3
Sinter for 3 hours
Sinter for 3 hours
Take the plug out of the mould, put it in the glass tube, and heat it in the vapour of boiling retene (394 °C) for 3 hours.
Àwọn irinṣẹ́ tí a nílò:
Àwọn tube ìdánwòReteneỌ̀gọ̀ Bunsen4
4
Cool it under the retene
Cool it under the retene
Remove the heat source and let the plug cool where it is. It is now sintered together into a tough mass.
Àwọn irinṣẹ́ tí a nílò:
Àwọn tube ìdánwòÀwọn ohun-èlò
1- 1 as required for the plugÀyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.