IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Screws: Cold Headed and Thread Rolled
Most screws are made in three steps: heading, thread rolling and coating. Wire from a coil is cut into blanks, and each blank is cold headed: a punch squeezes the end into a die shaped like the head, so a flat head comes from a flat die, with almost no waste. The thread is then rolled, not cut: the blank is rolled between hardened dies that press the thread into it. Rolling makes no swarf, needs a blank 15–20 % lighter than cutting would, gives a 10–20 % stronger thread, and runs at about one piece a second. Most screws are then zinc plated or blackened against rust.
Ilọsíwájú
About one per second (industrial)
Ìlànà
1
1
Cut blanks
Cut blanks
Wire from a coil is fed in and cut to the length of the screw: each piece is a blank.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okun waya irin10 kgÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìlù orí tútù2
2
Head
Head
A punch drives into the end of the blank and the metal flows into the head die. Complex heads take two blows; slotted heads get their slot cut afterwards.
Àwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìlù orí tútù3
3
Roll the thread
Roll the thread
The blank rolls between two flat dies, one fixed and one sliding, which press the thread into it cold.
Àwọn irinṣẹ́ tí a nílò:
Àwòṣe ìyí ìlà skúrù4
4
Coat
Coat
The screws are cleaned and given a coating against rust, such as zinc electroplating or black oxide.
5
5
Check
Check
Length, head and thread diameter are measured on samples.
Àwọn irinṣẹ́ tí a nílò:
Òṣùwọ̀n Kálípà Díjítà Ìnṣì 6Àwọn ohun-èlò
1- 10 kgÀyè
Àwọn irinṣẹ́ tó nílò
3Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.