IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Metal Bucket: Tapered Sheet Steel, Wired Rim, Bail and Lid
A bucket is a watertight vessel, a cylinder or tapered cone with an open top and a flat bottom, carried by a semicircular handle called the bail. Cut the side from steel sheet to the flat pattern of a cone, roll it, rivet and solder the seam, wire the rim, set in a bottom, hang a forged bail, and make a lid to fit.
The picture: a tapered metal well bucket with its bail.
Àárín
A day
Ìlànà
1
1
Mark and cut
Mark and cut
Mark the side as a ring sector (step 6) with dividers, plus a lap for the seam, and a bottom disc a little larger than the base. Cut them with snips.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ìwé Irin Pẹ́lẹ́2 ẹyọÀwọn irinṣẹ́ tí a nílò:
Kọ́mpàsì olójú méjì
Ìlàǹkàn irin2
2
Roll, rivet and solder
Roll, rivet and solder
Curve the side over the stake with a mallet until the ends lap. Drill and rivet the seam, then sweat solder into it with sal ammoniac as flux so it is watertight.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ìṣó irin8 ẹyọ
Wẹ́là tìnì-lédì0.1 kg
Amóníọ̀mù klóráìdì (NH₄Cl)0.01 kgÀwọn irinṣẹ́ tí a nílò:
Òkúta ìdá ìrísí
Òòlù Igi
Ìlù ọwọ́
Òòlù olórí ìtẹ̀ ìpakà
Irin ìsúdì3
3
Wire the rim and set the bottom
Wire the rim and set the bottom
Turn the top edge over a steel wire to stiffen the rim. Turn up the edge of the bottom disc, fit it inside the base, rivet it and solder it all round.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okun waya irin1 mÌṣó irin8 ẹyọWẹ́là tìnì-lédì0.1 kgÀwọn irinṣẹ́ tí a nílò:
Òkúta ìdá ìrísíÒòlù IgiÒòlù olórí ìtẹ̀ ìpakàÌlù ọwọ́Irin ìsúdì4
4
Ears and bail
Ears and bail
Forge two ears from sheet offcuts with a hole each and rivet them below the rim on opposite sides. Forge an iron rod into a semicircular bail with a hook at each end through the ears.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ọ̀pá róbótó irin lílù0.6 mÌṣó irin4 ẹyọ
Èédú2 as requiredÀwọn irinṣẹ́ tí a nílò:
Ìléru alágbẹ̀dẹ
Ìdí Alágbẹ̀dẹÒòlù olórí ìtẹ̀ ìpakà
Ẹmú alágbẹ̀dẹ
Ìbọ̀wọ́ wẹ́lídìn5
5
Lid
Lid
Cut a disc a little larger than the top and turn its edge down over the stake so it sits on the rim. Rivet on a strap handle.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ìwé Irin Pẹ́lẹ́1 ẹyọÌṣó irin2 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ìlàǹkàn irinÒkúta ìdá ìrísíÒòlù IgiÌlù ọwọ́6
6
The flat pattern of a tapered bucket
The flat pattern of a tapered bucket
Ń ṣí ìwé Jupyter…
Àwọn ohun-èlò
7- 2 ẹyọÀyè
- 22 ẹyọÀyè
- 0.2 kgÀyè
- 0.01 kgÀyè
- Àyè
- Àyè
- 2 as requiredÀyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.