IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours.
The picture: steel sewing needles (Wikimedia Commons).
Àárín
Half a day
Ìlànà
1
1
Cut, soften and straighten
Cut, soften and straighten
Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okùn duru70 mmÀwọn irinṣẹ́ tí a nílò:
Ẹ̀mú ìgé okùn oníkọ̀rọ̀
Ìléru alágbẹ̀dẹ
Ẹ̀mú imú gígùn
Ìdí Alágbẹ̀dẹ2
2
Point
Point
Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.
Àwọn irinṣẹ́ tí a nílò:
Àkójọ Ìfá
Ìdìmú Tábìlì
Gíláàsì ààbò3
3
Flatten and pierce the eye
Flatten and pierce the eye
Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.
Àwọn irinṣẹ́ tí a nílò:
Ìdí Alágbẹ̀dẹ
Òòlù olórí ìtẹ̀ ìpakà
Ìlù ọwọ́
Àkójọ Ìfá
Ìdìmú Tábìlì
Gíláàsì ààbò4
4
Harden in oil
Harden in oil
Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.
Àwọn irinṣẹ́ tí a nílò:
Ìléru alágbẹ̀dẹ
Ẹ̀mú imú gígùn
Àgbá ìtutù pẹ̀lú òróró
Gíláàsì ààbò5
5
Temper
Temper
Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.
Àwọn irinṣẹ́ tí a nílò:
Ààrò ìtọ́jú ooru
Thermocouple pẹ̀lú ìkà
Ìdí Alágbẹ̀dẹ
Òòlù olórí ìtẹ̀ ìpakà6
6
Scour and polish
Scour and polish
Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.
Àwọn irinṣẹ́ tí a nílò:
Aṣọ emery
Òróró òlífì
Ọṣẹ
Erùpẹ̀ igi
Awọ ìpọ́nbẹ
Àkójọ ÌfáÀwọn irinṣẹ́ tó nílò
17- Àyè
- Àyè
- Àyè
- Àyè
- Àyè
- Àyè
- Àyè
- Àyè
- Àyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.


