IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Woven Wire Screen Cloth: Hardened Crimped Steel Rods Locked by Driven Straight Rods (Robins, US 2,154,530, 1939)
Charlie

Ṣẹ́dá nipasẹ̀

Charlie

31. Oṣù Kẹwà 2026DE
0
0
0
0
0

Woven Wire Screen Cloth: Hardened Crimped Steel Rods Locked by Driven Straight Rods (Robins, US 2,154,530, 1939)

Screen cloth for gravel and stone wears out fast unless the steel is hard, but hard steel cracks when it is bent in weaving. Robins crimps the rods first, hardens them, and lays them up in layers without bending; straight hardened rods driven in endwise lock the whole panel under spring pressure. Result: coarse screen cloth, openings 5/8 in and up, hardened to as much as 60 Rockwell C; it lasted about twice as long. Source: Robins, US 2,154,530 (1939). He names only steel; a high-carbon steel is ours, since only a hardenable steel reaches 60 Rockwell C. Not given: crimp pitch, hardening heat and quench. Picture drawn by Youblob.
Ilọsíwájú
Factory process

Ìlànà

1

Crimp the rods

Cut steel rods, about 3/16 in diameter or more, to length and press-crimp three sets of them between dies. Keep a fourth set straight (no more than a quarter of all rods).

Àwọn ohun èlò fún ìgbésẹ̀ yìí:

Ọ̀pá wáyà irin líle oníkábọ́ọ̀nù púpọ̀Ọ̀pá wáyà irin líle oníkábọ́ọ̀nù púpọ̀1 as required

Àwọn irinṣẹ́ tí a nílò:

Ẹ̀rọ ìtẹ̀ àwo irinẸ̀rọ ìtẹ̀ àwo irin
2

Harden all the rods

Heat-harden the crimped and the straight rods before assembly; crimping first spares the dies. Robins reached 60 Rockwell C. Heat and quench: not given.

Àwọn irinṣẹ́ tí a nílò:

Ààrò muffleÀàrò muffle
Àpótí ìtutùÀpótí ìtutù
3

Lay up three crimped sets

Lay crimped set 1 in parallel on a table; lay set 3 across it, bends in register; lay set 2 parallel to set 1 on top, its bends opposite. Openings about 5/8 in or more.

Àwọn irinṣẹ́ tí a nílò:

Tábìlì iṣẹ́Tábìlì iṣẹ́
4

Drive in the straight rods

Drive the straight rods endwise, above set 2 and below set 1, alternating with set 3. They lock the panel by spring pressure without bending any rod for good; pulled out again, worn rods can be replaced.

Àwọn irinṣẹ́ tí a nílò:

Òòlù ńláÒòlù ńlá

Àwọn ohun-èlò

1

Àwọn irinṣẹ́ tó nílò

5

Ìtọ́nisọ́nà yìí ń ṣe

Blueprint tó jọra

Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà

CC0 Àgbègbè Gbogbogbò

Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.

Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.

Ìfọ̀rọ̀wérọ̀

(0)

Wọlé láti dara pọ̀ mọ́ ìfọ̀rọ̀wérọ̀

Ń gbé àwọn ọ̀rọ̀ wọlé...