Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Great Bellows of the Smelting Works: Pine Boards, Linden Bows, Ox-Hide and Iron Nozzle (Agricola, 1556)
Forge

Nilikha ni

Forge

14. Nobyembre 2026NO
11
0
0
0
0

Great Bellows of the Smelting Works: Pine Boards, Linden Bows, Ox-Hide and Iron Nozzle (Agricola, 1556)

The large blast bellows of a 16th-century smelting works, every part measured, from Agricola's De Re Metallica, Book IX (1556): two tapered boards of glued pine edged with linden, about 1.7 m long, two linden bows, two ox-hides nailed on with T-headed nails, a goatskin flap valve in the lower board, and a glued head carrying a 3 ft iron nozzle.
Abantado
About 2 weeks

Mga Tagubilin

1

Roman units in metric

Naglo-load ng Jupyter notebook…
2

Read De Re Metallica, Book IX

"Each bellows consists of a body and a head. The body is composed of two 'boards', two bows, and two hides."
3

Make the upper board

Glue two pieces of pine into a board a palm thick, 5 ft 3 palms long, 2-1/2 ft wide at the back (sides a little curved) and a cubit wide at the front, tapering to the head. Glue on linden edge strips, 7 digits wide at the back and 1-1/2 at the front, to take the nails. Cut an aperture 6 by 4 digits in the middle, 1 ft 3 palms from the head, with a sliding lid 2 palms 1 digit square and 3 digits thick running in mouldings a palm wide and 3 digits thick (or bore 2-3 round holes with plugs). Glue and peg a handle 7 palms or longer (2 palms wide, 1 thick on the board; rounded and 7 digits thick beyond), with a 2 ft cleat 2 palms wide and a palm thick over it and another 2 ft cleat underneath, 3 palms from the end.

Mga materyales para sa hakbang na ito:

Tablang pinoTablang pino2 piraso
Plantsang Kahoy na BasswoodPlantsang Kahoy na Basswood1 piraso
Pandikit na balat ng hayopPandikit na balat ng hayop1 piraso
Kahoy na TarugoKahoy na Tarugo1 piraso

Mga kailangang kasangkapan:

Lagaring PangkamayLagaring Pangkamay
KatamKatam
Mga paitMga pait
Barena at talimBarena at talim
Klamp na de-barasKlamp na de-baras
4

Make the lower board and flap valve

Make the lower board the same way and a cubit longer (the extra length is part of the head). About a cubit from the back, centred, cut an air-hole a foot long and 3 palms wide, leaving a rib a palm long and 1/3 digit wide across it. Make the flap a foot 3 digits by 3 palms 3 digits of thin board covered with goatskin, hair toward the ground, hinged with a doubled strip of leather a palm wide nailed to it and tied through two holes 7 digits apart. A foot beyond, fix a slightly elliptical iron ring 2 palms by 1 on a staple, 3 palms from the back, for the wooden bolt that holds the board to its frame (or use two iron screws).

Mga materyales para sa hakbang na ito:

Tablang pinoTablang pino2 piraso
Plantsang Kahoy na BasswoodPlantsang Kahoy na Basswood1 piraso
Pandikit na balat ng hayopPandikit na balat ng hayop1 piraso
Hilaw na balat ng kambingHilaw na balat ng kambing1 piraso
Panaling katadPanaling katad1 piraso
Metal na singsingMetal na singsing1 piraso
Mga pakoMga pako1 piraso

Mga kailangang kasangkapan:

Lagaring PangkamayLagaring Pangkamay
Mga paitMga pait
Barena at talimBarena at talim
MartilyoMartilyo
5

Make the bows

Make each bow as long as the upper board from four pieces of linden 3 digits thick: two long pieces 7 digits wide at the back and 2-1/2 at the front, a back piece 2 palms wide, its ends a little over a digit thick, bent to meet the long pieces, mortised, bored and pegged with glued pegs. Mortise in a crossbar a cubit from the head, a foot long without tenons and a palm 2 digits wide. Glue and peg two small pieces, 3 palms 2 digits long, a palm high and a digit thick, at the head to keep the bow ends off the air passage.

Mga materyales para sa hakbang na ito:

Plantsang Kahoy na BasswoodPlantsang Kahoy na Basswood2 piraso
Pandikit na balat ng hayopPandikit na balat ng hayop1 piraso
Kahoy na TarugoKahoy na Tarugo1 piraso

Mga kailangang kasangkapan:

Lagaring PangkamayLagaring Pangkamay
Mga paitMga pait
Barena at talimBarena at talim
Kahoy na PamukpokKahoy na Pamukpok
6

Make the head and nozzle

Glue the upper head board, a cubit long and 1-1/2 palms thick, onto the lower board's extension (a palm and a digit thick). Shape it a cubit wide at the back, 2 digits narrower 3 palms forward, then round the front to 2 palms 2 digits across and bind it with an iron ring 3 digits wide. Bore it for the nozzle: a pipe of thin iron plate 3 ft long, 3 digits across in front and a palm high by 2 palms wide at the back.

Mga materyales para sa hakbang na ito:

Tablang pinoTablang pino1 piraso
Pandikit na balat ng hayopPandikit na balat ng hayop1 piraso
Lata ng bakal (pinukpok)Lata ng bakal (pinukpok)1 piraso
Metal na singsingMetal na singsing1 piraso

Mga kailangang kasangkapan:

Lagaring PangkamayLagaring Pangkamay
Barena at talimBarena at talim
PandayanPandayan
PalihanPalihan
MartilyoMartilyo
7

Hide the bellows

Use ox-hide (far better than horse), two hides each 3-1/2 ft wide at the back. Lay a long leather thong along each board and bow and nail the hide through it with T-shaped iron nails 5 digits long, horns 2-1/2 digits long and half a digit wide, the horn of one nail almost touching the next along the boards; on each bow two nails in the back piece and four in each long piece, ten in all. Pine strips nailed over the hide on the long pieces guard against tearing; iron screws through strips over the hide hold even better.

Mga materyales para sa hakbang na ito:

Katad na kinurtido sa halamanKatad na kinurtido sa halaman2 piraso
Panaling katadPanaling katad1 piraso
Mga pakoMga pako1 piraso

Mga kailangang kasangkapan:

MartilyoMartilyo
Kutsilyo sa katadKutsilyo sa katad
GuntingGunting
8

Troubleshooting

Bellows troubleshooting.

Flow

Loading...
9

History and honest limits

From Georgius Agricola, **De Re Metallica** (1556), Book IX, translated by Herbert C. and Lou H. Hoover, 1912 (checked on the archive.org scan georgiusagricola00agri, pp. 362-365). The frame and the machinery that work the bellows are not covered here. The metric conversions (digit ~1.85 cm, palm ~7.4 cm, Roman foot ~29.6 cm, cubit ~44.4 cm) and the tools are ours.

Mga Materyales

10

Mga Kinakailangang Kasangkapan

11

Ang blueprint na ito ay gumagawa ng

Kaugnay na Blueprint

Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...