Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)
A shop brazing and tempering torch: a wall-hung pipe tank of gasoline or kerosene pumped up with a bicycle pump, feeding a 1/8 in pipe whose end is coiled round a short 1 in pipe; the flame heats the coil, the oil turns to gas, and it blasts out through a pinhole cap.
Two burners on a tee give a bigger heat.
Source: Popular Mechanics Shop Notes for 1909, pp. 861-862. Picture: the article's drawing.
Katamtaman
Unknown
Mga Tagubilin
1
1
Make the tank
Make the tank
Cap both ends of a 2 in pipe 20 in long. Drill three holes in the top cap: one for the rubber tube from a bicycle pump, one for a steam gauge, and one with a screw plug for filling with fuel oil.
Mga materyales para sa hakbang na ito:
Tubong bakal (makapal ang dingding, may sinulid na dulo)1 2 in x 20 in
Kasukasuan ng tubong may sinulid3 two caps, plug
Panukat ng Diin1 piraso
Tubong Goma1 pirasoMga kailangang kasangkapan:
Barenang de-kamay
Set sa paggawa ng sinulid ng turnilyo
Liyabe sa tubo
Bomba sa sahig para sa bisikleta2
2
Coil the burner
Coil the burner
Drill the bottom cap and connect a 1/8 in pipe D, any length, with a globe valve in it to set and shut off the oil. Fill the last 10 in of the pipe with lead, coil it round a 1 in pipe F 6 in long, and turn the end out to take two elbows and a short nipple; then melt the lead out. Drill a small hole in the centre of a 1/8 in cap and fit it on the end (E) so the hole lines up with the centre of pipe F.
Mga materyales para sa hakbang na ito:
Tubong bakal (makapal ang dingding, may sinulid na dulo)1 1/8 in, and 1 in x 6 inKasukasuan ng tubong may sinulid4 two elbows, nipple, 1/8 in cap
Balbulang globo1 pirasoMga kailangang kasangkapan:
Tingga
Butas-butas na sandok
PandayanBarenang de-kamayLiyabe sa tubo3
3
Start the burner
Start the burner
Hang a little cup holding three or four teaspoonfuls of oil just below the coil and light it to heat the coil; then pump up the tank and open the globe valve. For more heat connect two burners on a tee so their blasts meet.
Mga kailangang kasangkapan:
GaasBomba sa sahig para sa bisikletaMga Materyales
5- 1 1/8 in, and 1 in x 6 inPlaceholder
- 4 two elbows, nipple, 1/8 in capPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.