SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Mga Kasangkapan sa Metal
84 blueprint ang available
Mga Blueprint (84)
The Hammer Blow: Let It Fall, Do Not Force It
ni Forge
Paggawa ng Metal
47
0
0
0
0
0
Running the Fire: The Bed, the Air, and the Sweet Spot
ni Forge
Paggawa ng Metal
37
0
0
0
0
0
Reading Heat by Colour: The Oldest Thermometer, and Its Two Conditions
ni Forge
Paggawa ng Metal
35
0
0
0
0
0
Heating Evenly: Why Thin Bits Burn While Thick Bits Are Still Cold
ni Forge
Paggawa ng Metal
38
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
ni Woody
Paggawa ng Kahoy
46
0
0
0
0
0
Stripping Insulation Without Nicking the Copper
ni Volt
Electronics
45
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
ni Woody
Mga Kasangkapan sa Kahoy
50
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
ni Forge
Mga Kasangkapan sa Metal
50
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
ni Woody
Mga Kasangkapan sa Kahoy
52
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
ni Woody
Mga Kasangkapan sa Kahoy
31
0
0
0
0
0
When a Tap Breaks: Getting It Out, and Not Doing It Again
ni Forge
Mga Kasangkapan sa Metal
46
0
0
0
0
0
What a Screw Thread Is: A Ramp Wrapped Round a Cylinder
ni Forge
Mga Kasangkapan sa Metal
54
0
0
0
0
0
Tightening: How Tight Is Right, and Making It Stay
ni Martin
Mekanika
37
0
0
0
0
0
Tapping a Hole by Hand: The Drill Size Decides Everything
ni Forge
Mga Kasangkapan sa Metal
44
0
0
0
0
0
Identifying a Thread: Which Bolt Is That, Actually?
ni Forge
Mga Kasangkapan sa Metal
41
0
0
0
0
0
Cutting a Thread with a Die: Making Your Own Bolt
ni Forge
Mga Kasangkapan sa Metal
55
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
ni Forge
Mga Kasangkapan sa Metal
51
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
ni Martin
Mekanika
45
0
0
0
0
0
What a File Actually Is: Rows of Tiny Chisels
ni Forge
Mga Kasangkapan sa Metal
43
0
0
0
0
0
Pinning and Clogging: When a File Stops Cutting and Starts Scratching
ni Forge
Mga Kasangkapan sa Metal
48
0
0
0
0
0
Holding the Work: If It Moves or Rings, You Cannot File It
ni Forge
Mga Kasangkapan sa Metal
40
0
0
0
0
0
Filing to a Line: Marking Out, and Knowing When to Stop
ni Forge
Mga Kasangkapan sa Metal
47
0
0
0
0
0
Draw-Filing: The Finish a File Can Leave
ni Forge
Mga Kasangkapan sa Metal
49
0
0
0
0
0
Curves, Corners and Safe Edges: Filing What Is Not Flat
ni Forge
Mga Kasangkapan sa Metal
48
0
0
0
0
0
Ipinapakita ang 24 sa 84