SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Paggawa ng Metal
586 blueprint ang available • 8 subkategorya
Mag-browse ng Subkategorya
Mga Blueprint (586)
The Solderless Side Seam: A Lock That Cannot Unroll
ni Forge
Paggawa ng Metal
25
0
0
0
0
0
How Far a Sheet Will Stretch: The Cupping Test and the Circle Grid
ni Mary
Mga Materyales
41
0
0
0
0
0
Turning the Corner: The Right-Angle Head
ni Forge
Paggawa ng Metal
40
0
0
0
0
0
A Blade That Goes Where No Frame Can
ni Forge
Paggawa ng Metal
36
0
0
0
0
0
Hitting a Bolt Instead of Leaning on It
ni Martin
Mekanika
39
0
0
0
0
0
Set and Presetting: Why a Spring Goes Weak Without Getting Softer
ni Emma
Inhinyeriya
45
0
0
0
0
0
Spring Fatigue: It Is the Swing That Breaks It
ni Emma
Inhinyeriya
32
0
0
0
0
0
Spring Index: Why a Fat Wire on a Small Coil Fights Back
ni Emma
Inhinyeriya
43
0
0
0
0
0
Reading a Plating Fault: Burnt, Pitted, Dull, Peeling
ni Charlie
Kemistri
34
0
0
0
0
0
Current Density: Edges Plate Thick and Recesses Do Not Plate At All
ni Charlie
Kemistri
51
0
0
0
0
0
The Surface Is the Job: Plating Fails Before the Current Is Switched On
ni Charlie
Kemistri
47
0
0
0
0
0
Arc Eye and Fume: Measure the Two Injuries That Arrive After You Finish
ni Forge
Paggawa ng Metal
30
0
0
0
0
0
Reading a Weld: Undercut, Porosity, Slag and Overlap Each Name a Cause
ni Forge
Paggawa ng Metal
43
0
0
0
0
0
Distortion and Sequence: The Weld Pulls, So Decide Where It Pulls To
ni Forge
Paggawa ng Metal
49
0
0
0
0
0
Fillet and Butt: Sizing the Weld the Joint Actually Needs
ni Forge
Paggawa ng Metal
46
0
0
0
0
0
Penetration and Fusion: A Weld That Sits on Top Is Not a Weld
ni Forge
Paggawa ng Metal
43
0
0
0
0
0
Running a Bead: Travel Speed Is Not a Matter of Taste
ni Forge
Paggawa ng Metal
43
0
0
0
0
0
Striking and Holding an Arc: Four Things Under Your Hand at Once
ni Forge
Paggawa ng Metal
37
0
0
0
0
0
Joint Preparation: Most of a Weld Is Decided Before the Arc Is Struck
ni Forge
Paggawa ng Metal
39
0
0
0
0
0
Fettling: What Happens After the Mould Is Broken Open
ni Forge
Paggawa ng Metal
44
0
0
0
0
0
Reading a Casting: Porosity, Cold Shuts and Inclusions Each Name a Cause
ni Forge
Paggawa ng Metal
39
0
0
0
0
0
Pouring Temperature: Too Cold Misruns, Too Hot Tears the Mould
ni Forge
Paggawa ng Metal
35
0
0
0
0
0
Risers: Metal Shrinks When It Freezes, and the Hole Goes Somewhere
ni Forge
Paggawa ng Metal
41
0
0
0
0
0
Gating: Getting the Metal In Without Wrecking the Mould
ni Forge
Paggawa ng Metal
44
0
0
0
0
0
Ipinapakita ang 24 sa 586