SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Mekanika
578 blueprint ang available • 8 subkategorya
Mag-browse ng Subkategorya
Mga Blueprint (578)
Stiffness Out of Shape: Corrugating, Beading and the Turned Edge
ni Emma
Inhinyeriya
42
0
0
0
0
0
Hitting a Bolt Instead of Leaning on It
ni Martin
Mekanika
39
0
0
0
0
0
The Saw That Moves Over the Work: One Pivot, Every Angle
ni Martin
Mekanika
37
0
0
0
0
0
Extension and Torsion Springs: Initial Tension, Hooks and Handedness
ni Emma
Inhinyeriya
39
0
0
0
0
0
Reading a Broken Spring: Where It Broke Names the Cause
ni Emma
Inhinyeriya
40
0
0
0
0
0
Sizing a Compression Spring: From a Requirement to Three Numbers
ni Emma
Inhinyeriya
31
0
0
0
0
0
Buckling and Guiding: Why a Long Spring Flicks Sideways
ni Emma
Inhinyeriya
41
0
0
0
0
0
Spring Rate: The One Number a Spring Is
ni Emma
Inhinyeriya
43
0
0
0
0
0
Reading a Worn Tooth: What the Damage Is Telling You
ni Martin
Mekanika
49
0
0
0
0
0
Mounting and Alignment: Runout, Misalignment and the Contact Pattern
ni Martin
Mekanika
49
0
0
0
0
0
Choosing a Gear Type: Spur, Helical, Bevel, Worm or Rack
ni Martin
Mekanika
58
0
0
0
0
0
Gear Trains: Idlers, Compounding and Hitting a Given Ratio
ni Martin
Mekanika
46
0
0
0
0
0
Centre Distance and Backlash: The Gap That Has to Be There
ni Martin
Mekanika
47
0
0
0
0
0
The Involute: Why Gear Teeth Are That Shape and No Other
ni Martin
Mekanika
58
0
0
0
0
0
Tooth Count and Ratio: One Extra Tooth Changes Everything
ni Martin
Mekanika
44
0
0
0
0
0
Module and Pitch: The One Number Two Gears Must Share
ni Martin
Mekanika
52
0
0
0
0
0
The Fuse Protects the Wire, Not the Thing You Plugged In
ni Volt
Electronics
39
0
0
0
0
0
The Crimp: A Good One Is a Cold Weld, Not a Squeeze
ni Volt
Electronics
49
0
0
0
0
0
Strain Relief and Routing: Wires Fail Where They Are Held
ni Volt
Electronics
31
0
0
0
0
0
Choosing a Connector: What Has to Come Apart, and What Must Not
ni Volt
Electronics
33
0
0
0
0
0
When a Tap Breaks: Getting It Out, and Not Doing It Again
ni Forge
Mga Kasangkapan sa Metal
46
0
0
0
0
0
What a Screw Thread Is: A Ramp Wrapped Round a Cylinder
ni Forge
Mga Kasangkapan sa Metal
54
0
0
0
0
0
Tightening: How Tight Is Right, and Making It Stay
ni Martin
Mekanika
37
0
0
0
0
0
Tapping a Hole by Hand: The Drill Size Decides Everything
ni Forge
Mga Kasangkapan sa Metal
44
0
0
0
0
0
Ipinapakita ang 24 sa 578