SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Pine Boards with a Chainsaw Mill
A chainsaw mill is a frame that holds the saw's bar flat at a set height, so the chain rips a log lengthways into boards. The first cut rides on a straight board screwed to the log; every later cut rides on the flat face before it. The green boards are then stacked on stickers to air-dry.
Pine dries fast: a 25 mm board can reach about 14 % moisture in 60 to 90 days in good drying weather. Oak and other slow species take far longer.
Katamtaman
1 day milling, 2–3 months drying
Mga Tagubilin
1
1
Pick and prop the log
Pick and prop the log
Choose a straight pine log, 2.5–3 m long, without large knots. Prop it on two short logs so it cannot roll and the chain will not reach the ground.
Mga materyales para sa hakbang na ito:
Mga trosong malambot na kahoy1 pirasoMga kailangang kasangkapan:
Panukat na Tape2
2
Fit the mill
Fit the mill
Bolt the mill to the chainsaw bar following its maker's instructions. A ripping chain cuts along the grain faster and smoother than a crosscut chain.
Mga kailangang kasangkapan:
Chainsaw (antas propesyonal na panggubat)
Kuwadro ng lagaring de makina3
3
Screw on the guide board
Screw on the guide board
Screw a straight board along the top of the log, level from end to end, as the rail for the first cut. Check it with the straightedge and level.
Mga materyales para sa hakbang na ito:
Mga turnilyong pangkahoy6 pirasoMga kailangang kasangkapan:
Tablang pino
Walang-Kableng Barena
Panuwid
Antas na May Burbuha4
4
First cut
First cut
Wearing helmet with visor, ear protection, gloves and boots, run the mill along the guide board and take off the top slab. Remove the guide board.
Mga kailangang kasangkapan:
Chainsaw (antas propesyonal na panggubat)Kuwadro ng lagaring de makina
Helmet na pangkaligtasan
Pantakip sa tainga
Guwantes na Katad Pangtrabaho
Botang pangkaligtasan na bakal ang dulo5
5
Cut the boards
Cut the boards
Set the mill a few millimetres thicker than the finished board, to allow for shrinking and planing. Run each cut on the flat face left by the one before.
Mga kailangang kasangkapan:
Chainsaw (antas propesyonal na panggubat)Kuwadro ng lagaring de makinaPanukat na Tape6
6
Seal the ends
Seal the ends
Paint both ends of every board with end sealer the same day, to stop them splitting as they dry.
Mga materyales para sa hakbang na ito:
Pansara ng dulo (waks na parapina)0.5 litro7
7
Sticker the stack
Sticker the stack
On a level base at least 30 cm off the ground, lay the boards in layers with a gap between them, each layer on stickers every 40–60 cm, the stickers one above the other.
Mga materyales para sa hakbang na ito:
Panipis na kahoy (pang-agwat sa pagpapatuyo)30 pirasoMga kailangang kasangkapan:
Paleta ng kahoyAntas na May Burbuha8
8
Cover and weight
Cover and weight
Cover the top of the stack against rain and lay weight on it to keep the top boards flat; leave the sides open to the air.
Mga kailangang kasangkapan:
Trapal9
9
Measure the moisture
Measure the moisture
After 2 months, read a board from the middle of the stack. Air-dry outdoors reaches about 12–15 %; bring boards for furniture indoors to settle at 6–8 % before working them.
Mga kailangang kasangkapan:
Panukat ng halumigmig10
10
Troubleshooting
Troubleshooting
Chainsaw milling troubleshooting.
Flow
Loading...
Mga Materyales
4- 1 pirasoPlaceholder
- 6 pirasoPlaceholder
- 0.5 litroPlaceholder
- Placeholder
Mga Kinakailangang Kasangkapan
14- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.