Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)
A hand-held digital tachometer. You press the contact head on its shaft against the end of a turning shaft and push the thumb button; a slotted disk inside chops a light beam into pulses, and the pulses counted in a fixed time, set by a quartz clock, appear in the window as the speed. A latch holds the reading after you take the tachometer away, so you can read it even where you could not see the window while measuring.
Result: a contact tachometer that shows revolutions per unit time and keeps the last reading.
Source: Y. Sugiyama (Shimpo Kogyo), US 4,000,465 (1976). Unknown: the number of holes, the clock, the gate time and the circuit details. Picture: the patent drawing.
Abantado
Unknown
Mga Tagubilin
1
1
Make the housing and measuring shaft
Make the housing and measuring shaft
Make a cylindrical housing to hold in one hand, with a window in its side for the reading and a push button for the power switch where the thumb falls. Run a measuring shaft out of the front end in bearings and fit a contact head on its tip to press against the shaft being measured. Not given: materials, sizes. Ours: aluminium tube, a ball bearing.
Mga materyales para sa hakbang na ito:
Tubo na aluminyo1 housing
Hindi alam na metal1 measuring shaft
Ball Bearing1 piraso
Hindi kilalang materyal1 contact headMga kailangang kasangkapan:
Torno para sa Metal
Barenang de-kamay
Hindi alam na sukat2
2
Make the pulse generator
Make the pulse generator
Fix a disk on the measuring shaft with a ring of small holes evenly spaced near its edge. Put a light source on one side of the disk and a photodetector on the other: each hole passing makes one pulse. Shape and amplify the pulses. Not given: the number of holes. Ours: an LED and a photodiode.
Mga materyales para sa hakbang na ito:
Hindi kilalang materyal1 slotted disk
Sari-saring LED1 light source
Photodiode (BPW34)1 photodetector
Resistensya1 setMga kailangang kasangkapan:
Barenang de-kamay3
3
Build the counting circuit
Build the counting circuit
Divide a quartz oscillator's clock down to gate pulses one unit of time long. Pass the measurement pulses through an AND gate during each gate pulse into a counter. At the start of each gate pulse a reset pulse clears the counter. After the gate pulse ends, the first measurement pulse that arrives triggers a latch pulse that loads the new count into the display. If the head has been taken off the shaft, no pulse arrives, no latch pulse is made, and the display keeps the last reading until the next measurement or until the power is switched off. Not given: the clock frequency and gate time. Ours: logic ICs and a seven-segment display.
Mga materyales para sa hakbang na ito:
Printed circuit board (PCB)1 piraso
Quartz crystal1 piraso
Sari-saring IC na lohika1 divider, AND gate, counter, latch, reset
Tagapagpaandar ng Display na may Pitong Segment1 piraso
Apat-na-Digit na Display na may Pitong Segment1 piraso
Kawad na Panghinang1 as neededMga kailangang kasangkapan:
Panghinang4
4
Power it and measure
Power it and measure
Fit the battery and the thumb button as the power switch. Press the contact head against the end of the turning shaft so it turns with it, push the button, and read the revolutions in the window, now or after you take the tachometer away.
Mga materyales para sa hakbang na ito:
Baterya1 piraso
Pindutan1 pirasoMga kailangang kasangkapan:
PanghinangMga Materyales
15- 1 housingPlaceholder
- 1 measuring shaftPlaceholder
- Placeholder
- 1 slotted diskPlaceholder
- 1 light sourcePlaceholder
- 1 photodetectorPlaceholder
- 1 setPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 divider, AND gate, counter, latch, resetPlaceholder
- Placeholder
- Placeholder
- 1 as neededPlaceholder
- 1 pirasoPlaceholder
- Placeholder
Mga Kinakailangang Kasangkapan
4- Placeholder
- Placeholder
- Placeholder
- 2 vendors sell this, none ship to you yetPlaceholder
Mga Materyales ng Nakakonektang Blueprint
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.