SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Nilikha ni

Penny

14. Oktubre 2026DK
15
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Katamtaman
Two to three days

Mga Tagubilin

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Mga materyales para sa hakbang na ito:

Patag na barang tool steelPatag na barang tool steel1 piraso

Mga kailangang kasangkapan:

Kikil na Pang-metalKikil na Pang-metal
Barenang de-kamayBarenang de-kamay
Digital na Kalibrador 6 PulgadaDigital na Kalibrador 6 Pulgada
Pandayan ng pandayPandayan ng panday
Timbang pampatigasTimbang pampatigas
Salaming pangkaligtasanSalaming pangkaligtasan
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Mga materyales para sa hakbang na ito:

Tira ng matigas na kahoyTira ng matigas na kahoy2 piraso
Bilog na Bara ng Malambot na AseroBilog na Bara ng Malambot na Asero0.3 m

Mga kailangang kasangkapan:

Kikil na Pang-metalKikil na Pang-metal
Pandayan ng pandayPandayan ng panday
Timbang pampatigasTimbang pampatigas
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Mga materyales para sa hakbang na ito:

Lapad na BronseLapad na Bronse1 piraso
Sinulid na linen na may kandilaSinulid na linen na may kandila3 m

Mga kailangang kasangkapan:

Gunting na pangyeroGunting na pangyero
Barenang de-kamayBarenang de-kamay
Kikil na Pang-metalKikil na Pang-metal
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Mga kailangang kasangkapan:

Kikil na Pang-metalKikil na Pang-metal
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Mga materyales para sa hakbang na ito:

Bareta ng tansong dilawBareta ng tansong dilaw2 kg
UlingUling1 as required
Buhangin sa paghuhulmaBuhangin sa paghuhulma5 kg

Mga kailangang kasangkapan:

Pandayan ng pandayPandayan ng panday
Krisol na Luwad na Matibay sa ApoyKrisol na Luwad na Matibay sa Apoy
Sipit ng KrisolSipit ng Krisol
Kahong panghulma (itaas at ibaba)Kahong panghulma (itaas at ibaba)
Mga guwantes sa paghihinangMga guwantes sa paghihinang
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Mga materyales para sa hakbang na ito:

TubigTubig1 litro

Mga kailangang kasangkapan:

Silindrong may sukatanSilindrong may sukatan
Kikil na Pang-metalKikil na Pang-metal
7

A binary set of weights

Naglo-load ng Jupyter notebook…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Mga Materyales

9

Mga Kinakailangang Kasangkapan

12

Kaugnay na Blueprint

Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...