Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)
Ear muffs that seal well and still stop low-pitched noise. Each ear is covered by a rigid cup on a cushion made of a thin PVC tube, emptied of air and part-filled with liquid. Pressed on, the liquid flows round the whole rim and fits the cushion to the head, yet cannot compress, so the cup does not vibrate as a whole and pass the sound in. A sprung headband with a pad holds the cups on ball joints.
Result: circumaural ear defenders effective against low-frequency noise.
Source: E. A. G. Shaw and G. J. Thiessen (National Research Council of Canada), US 2,801,423 (1957). Unknown: sizes and the attenuation achieved. Picture: the patent drawing.
Katamtaman
Unknown
Mga Tagubilin
1
1
Make the cups
Make the cups
Make two rigid, non-porous cups to go over the ears, of wood, a hard plastic or a light metal such as aluminium. Widen each rim to about the width of the cushion, and make a small hole in the rim for the cushion's filling nipple. Fix a ball joint on the back of each cup. Not given: sizes.
Mga materyales para sa hakbang na ito:
Hindi kilalang materyal2 tasa
Hindi alam na metal2 ball jointsMga kailangang kasangkapan:
Torno para sa Metal
Hindi alam na sukat2
2
Make the liquid cushions
Make the liquid cushions
For each cup make an endless tube of thin, pliable but non-stretching plasticised PVC, 0.005 to 0.01 in thick, with a filling nipple. Draw out almost all the air, then fill it with liquid to more than a quarter but well under the whole of its cross-section: enough to reach right round the rim when pressed, not so much that it cannot seal. Fix it on the rim with the nipple in the hole. Ours: water as the liquid. Not given: tube size.
Mga materyales para sa hakbang na ito:
Plantsang PVC1 thin plasticised PVC tube
Tubig1 fillingMga kailangang kasangkapan:
Set ng heringgilya3
3
Fit the headband and wear them
Fit the headband and wear them
Make a resilient headband frame with a sponge-rubber pad at its middle and a wire loop at each end. Through each loop pass a threaded stub from the cup's ball joint, with a washer, and tighten with a wing nut. Put the cups over the ears: the cushions take the shape of the head and seal, while the cups stay still against the low-frequency sound. Ours: spring steel for the frame.
Mga materyales para sa hakbang na ito:
Kawad na asero para sa resorte1 frame and loopsHindi kilalang materyal1 sponge rubber padHindi alam na metal2 threaded stubs
Patag na Sinturon2 piraso
Tuwerkang paru-paro2 pirasoMga kailangang kasangkapan:
Plais na bilog ang duloMga Materyales
7- 1 sponge rubber padPlaceholder
- 2 threaded stubsPlaceholder
- 1 thin plasticised PVC tubePlaceholder
- 1 fillingPlaceholder
- 1 frame and loopsPlaceholder
- 2 pirasoPlaceholder
- 2 pirasoPlaceholder
Mga Kinakailangang Kasangkapan
4- Placeholder
- Placeholder
- Placeholder
- Placeholder
Mga Materyales ng Nakakonektang Blueprint
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.