Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
High-Speed Steel, Charge 1: Crucible-Melted Tungsten-Chrome-Molybdenum Steel (Carnegie & Gladwyn 1918)
High-speed steel holds its edge when it is cutting hot. In Sheffield it was made like other crucible tool steel: the best Swedish bar iron melted in small clay pots in a coke fire, with tungsten, chromium and molybdenum added to the liquid iron. This is the first of three typical charges given by Carnegie and Gladwyn: 82 lb iron, 13 lb tungsten powder, 5 lb ferro-chrome and 4 lb ferro-molybdenum for 100 lb of steel.
Source: D. Carnegie and S. C. Gladwyn, Liquid Steel (1918), pp. 74-77, 106-107 and 113. Unknown: how the Swedish iron, the tungsten powder and the ferro-molybdenum are made; the melting time; and how the ingot is worked into bar. The book stops at the liquid steel, so these are linked to unknown heads. Picture: the book's Fig. 29, crucible furnaces at Samuel Osborn & Co., Sheffield.
Dalubhasa
1 day
Mga Tagubilin
1
1
Weigh charge 1
Weigh charge 1
For 100 lb of steel: 82 lb best Swedish bar iron, cut up; 13 lb tungsten powder (96 to 98 % tungsten); 5 lb ferro-chrome (60 % chromium); 4 lb ferro-molybdenum (80 % molybdenum). Unknown: how the Swedish iron, tungsten powder and ferro-molybdenum are made. The book only lists them.
Mga materyales para sa hakbang na ito:
Bakal na barang Swedish82 libra
Pulbos na tungsten13 libra
Ferokromo5 libra
Ferromolybdenum4 libraMga kailangang kasangkapan:
Timbangang panimbang2
2
Set two clay crucibles in the melting hole
Set two clay crucibles in the melting hole
Tool steels are melted in small crucibles, about 55 lb each, two to a hole in a Huntsman coke furnace (ours: the 100 lb charge split between the two). Stand them on fireclay stands on the fire bars, straight from the annealing furnace, and fill the hole with coke up to their tops. Use the best washed coke, as free from sulphur as possible: sulphur gets into the steel even through the lid. When the pots are white hot, throw in a little sand to fuse them onto their stands.
Mga kailangang kasangkapan:
Pugon na may crucible
Krisol na Luwad na Matibay sa Apoy
Kokeng metalurhiko
Buhangin
Sipit ng Krisol3
3
Melt the iron, then add the alloys
Melt the iron, then add the alloys
Charge the cut iron, put on the clay lids, fill the hole with coke and close the cover. Renew the fire as it burns through. Add the tungsten powder and ferro-alloys to the liquid iron and melt them in. Unknown: the melting time and temperature for this charge. The book says only that tool steel takes longer than ordinary steel. About 3½ tons of coke go to each ton of high-speed steel.
Mga kailangang kasangkapan:
Pugon na may crucibleKokeng metalurhikoSipit ng Krisol4
4
Pull out, skim and teem
Pull out, skim and teem
Lift each pot out with the pulling-out tongs (arms and legs covered with wet sacking), take off the lid and skim the slag with a mop, then pour the steel into ingot moulds. Unknown: the ingot size. A clay crucible lasts about 3 heats.
Mga kailangang kasangkapan:
Sipit ng Krisol
Hulmahan ng lingote
Guwantes na Matibay sa Init5
5
Work the ingot into round bar
Work the ingot into round bar
Unknown: how the ingot is heated, hammered or rolled, and annealed into round bar. Carnegie and Gladwyn stop at the liquid steel, so this step is linked to an unknown head until a source gives it.
Mga kailangang kasangkapan:
Hindi kilalang iskedyul ng pagpandayMga Materyales
4- 82 libraPlaceholder
- 13 libraPlaceholder
- 5 libraPlaceholder
- 4 libraPlaceholder
Mga Kinakailangang Kasangkapan
9- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.