SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Hot Glue Gun: Weller & Brassaw, 1973
Carl E. Weller and Alden J. Brassaw, for Cooper Industries, patented this glue gun in 1973, US 3,744,921. A stick of solid hot-melt adhesive drops through a loading well into a tubular melt chamber that narrows to a nozzle. Mica sheet wound with nichrome wire and closed by a metal sleeve heats the chamber, under a thermostat. Instead of a thumb, ratchet or feed wheel pushing the stick, a spring drives a Teflon-tipped piston forward against it. A valve pin in the nozzle keeps it closed against dripping; pressing the projecting pin on the work opens it and the glue flows.
Abantado
Factory process
Mga Tagubilin
1
1
Housing and melt chamber
Housing and melt chamber
Fit the elongated tubular melt chamber between the two pistol-shaped housing halves: a uniform cylindrical barrel with a loading well opening through the top of the housing, a converging conical forward part and a threaded end.
Mga materyales para sa hakbang na ito:
Mga kalahati ng kaha ng glue gun1 piraso
Pantubong silid na tunawan1 pirasoMga kailangang kasangkapan:
Set ng mga distornilyador2
2
Heater
Heater
Wrap mica sheeting spirally round the barrel with nichrome windings between the layers, close it in a tubular metal sleeve, and fit the thermostat in its well against it.
Mga materyales para sa hakbang na ito:
Nichrome na heater na nakabalot sa mica, may thermostat1 piraso
Kawad na nichrome1 as required
Lata ng mika1 as requiredMga kailangang kasangkapan:
Plais na Kombinasyon3
3
Nozzle and valve
Nozzle and valve
Screw the nozzle onto the threaded end. Inside it, the valve pin's enlarged portion seats against the bore's step and its tip projects from the outlet; glue pressure holds it shut until the tip is pressed against the work.
Mga materyales para sa hakbang na ito:
Nozzle ng pandikit na may balbula1 pirasoMga kailangang kasangkapan:
Llaveng ingles4
4
Plunger
Plunger
Fit the plunger, a Teflon piston on a rod guided by a plate, behind the loading well, with its knob outside the housing; couple it to the spring in its tube through the pull device so the spring pushes the glue stick forward.
Mga materyales para sa hakbang na ito:
Plunger na may spring at Teflon na piston1 pirasoMga kailangang kasangkapan:
Set ng mga distornilyadorMga Materyales
7- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- Placeholder
- 1 as requiredPlaceholder
- 1 as requiredPlaceholder
- Placeholder
- Placeholder
Mga Kinakailangang Kasangkapan
3- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.