Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Nilikha ni

Forge

13. Nobyembre 2026NO
4
0
0
0
0

Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat front horseshoe made from one iron bar, as taught at the Dresden shoeing school: bend each branch over the anvil, bevel and flatten it, concave the hoof side, fuller the crease, and stamp and pritchel the nail holes. From Lungwitz and Adams, A Text-Book of Horseshoeing (11th edition, 1913). "Any ordinary shoe can and should be completed in the rough in two heats." Fitting and nailing the shoe to the horse are not covered here.
Katamtaman
8-15 minutes a pair, once practised

Mga Tagubilin

1

Bar length and sizes

Naglo-load ng Jupyter notebook…
2

Read Lungwitz and Adams

"A shoe should be made thoughtfully, but yet quickly enough to make the most of the heat."
3

Measure the hoof

Measure the length of the hoof from the point of the toe to the buttress, and its greatest width. Added together they give the length of the bar. To keep the exact outline, set the hoof on stiff paper and trace round the wall with a pencil.

Mga kailangang kasangkapan:

Panukat na TapePanukat na Tape
LapisLapis
Makakapal na sheet ng papelMakakapal na sheet ng papel
4

Cut the bar

Choose good, tough iron, of a width and thickness that needs the least working. Cut the bar to the length you measured; a bar shoe or a shoe with heel calks needs a longer bar.

Mga materyales para sa hakbang na ito:

Baras na pandayang bakalBaras na pandayang bakal1 piraso

Mga kailangang kasangkapan:

Pandayan ng pandayPandayan ng panday
Pait na pamutol sa palihanPait na pamutol sa palihan
Sipit ng PandaySipit ng Panday
Martilyong pambilogMartilyong pambilog
5

Bend the outer branch

Heat the bar white-hot just beyond its middle. Lay the head of the sledge across one end of the anvil face, hold the cold end of the bar on it with the hot end on the face, and bend the bar into a half-circle with the round head of the turning hammer. Make the outer branch first, and the right shoe first in a pair. Draw out the end to width and thickness with the sledge.

Mga kailangang kasangkapan:

Pandayan ng pandayPandayan ng panday
Palihang may tukaPalihang may tuka
ParagosParagos
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
6

Bevel and flatten

Lay the bent branch obliquely across the heel of the horn, turn it to the right onto an edge, and bevel it diamond-shaped from toe to end. Flatten it on the face: bending stretched and thinned the outer edge and thickened the inner one, so leave the inner edge a trifle thinner. Go over it lightly on the horn with the flat face of the hammer to shape it.

Mga kailangang kasangkapan:

Palihang may tukaPalihang may tuka
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
7

Concave and fuller

Concave (seat) the hoof side, ending about 3/4 in from the end of the branch, or leave it flat for an arched sole. Turn the branch and fuller it: set the fuller about 1/12 in from the edge on small shoes, more on large ones, and lead it from the end of the branch to the toe, twice, to about two-thirds of the thickness.

Mga kailangang kasangkapan:

Palihang may tukaPalihang may tuka
ParagosParagos
Fuller (bakal na panguka)Fuller (bakal na panguka)
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
8

Stamp and pritchel the nail holes

Stamp the nail holes in the crease and punch them through with the pritchel. Six are enough for a medium shoe, all in the front half and none at the toe. Their distance from the outer edge equals the thickness of the wall there; incline the toe holes a little inward and punch the quarter holes straight. Each hole tapers from the ground side to the hoof side.

Mga kailangang kasangkapan:

Palihang may tukaPalihang may tuka
Mainit na pambutasMainit na pambutas
Pambutas ng bakal ng kabayoPambutas ng bakal ng kabayo
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
9

Finish the branch, then the other

Run over the surfaces, go over the outer edge on the horn, and hammer the bearing surface smooth and level. Make the inner branch the same way, turned to the left and fullered from toe to heel. The finished front shoe is round at the toe and about 7/16 in thick; a hind shoe is bent more pointed at the toe and needs no concaving, only the inner edge rounded.

Mga kailangang kasangkapan:

Pandayan ng pandayPandayan ng panday
Palihang may tukaPalihang may tuka
Martilyong pambilogMartilyong pambilog
Fuller (bakal na panguka)Fuller (bakal na panguka)
Mainit na pambutasMainit na pambutas
Pambutas ng bakal ng kabayoPambutas ng bakal ng kabayo
Sipit ng PandaySipit ng Panday
10

Troubleshooting

Horseshoe troubleshooting.

Flow

Loading...
11

History and honest limits

From **A Text-Book of Horseshoeing, for Horseshoers and Veterinarians**, by A. Lungwitz (Dresden shoeing school) and John W. Adams (University of Pennsylvania), 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F, "Making Shoes"; wall thicknesses after Mayer. Not covered: trimming, fitting and nailing the shoe to the hoof, clips, calks and special shoes. The book names no forge fuel. The metric figures are ours.

Mga Materyales

1

Mga Kinakailangang Kasangkapan

12

Ang blueprint na ito ay gumagawa ng

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...