SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Nalbinding a Wool Sock in the Oslo Stitch — The Looped Fabric Before Knitting
Long before knitting, people made warm, hard-wearing socks and mittens by nalbinding — looping short lengths of wool with a single flat needle. Unlike knitting, which pulls loops through loops with two rods and can unravel, nalbinding passes the whole working thread through each stitch, giving a dense, felt-firm fabric that will not run. This blueprint works the simple Oslo stitch into a tube for a sock or mitten, joining new wool with a felted splice rather than a knot — exactly as the Vikings did.
Katamtaman
4
Mga Tagubilin
1
1
Cut a short working length
Cut a short working length
Cut about an arm's length of wool yarn — not a whole ball. In nalbinding the entire length is pulled through every stitch, so you work with short pieces and splice on more as needed.
Mga materyales para sa hakbang na ito:
Ikid ng Sinulid na Lana1 pirasoMga kailangang kasangkapan:
Gunting2
2
Thread the flat needle
Thread the flat needle
Thread the yarn through the eye of the flat nalbinding needle. The needle is broad, blunt and eyed at one end — bone, antler or wood — and never has a hook.
Mga kailangang kasangkapan:
Karayom sa nalbinding3
3
Make the foundation loops
Make the foundation loops
Loop the yarn around your thumb and make a short chain of starting loops. These foundation loops are the base row that every following stitch will anchor into.
Mga kailangang kasangkapan:
Karayom sa nalbinding4
4
Work the Oslo stitch
Work the Oslo stitch
Pass the needle under the thumb loop and up through the working loop to form the Oslo stitch — the simplest nalbinding stitch. Draw each stitch snug and even, building the first row.
Mga kailangang kasangkapan:
Karayom sa nalbinding5
5
Join into a round
Join into a round
For a sock or mitten, connect the ends of the first row into a ring by stitching the last stitch into the first, so you can then work round and round to form a tube.
Mga kailangang kasangkapan:
Karayom sa nalbinding6
6
Work in a spiral
Work in a spiral
Continue in a spiral, anchoring each new Oslo stitch into the loop of the row below. Keep the tension steady so the tube grows even in width — this becomes the leg of the sock.
Mga kailangang kasangkapan:
Karayom sa nalbinding7
7
Splice in new yarn
Splice in new yarn
When the length runs short, join a new piece with a felted splice, not a knot: untwist and overlap the two wool ends, wet them, and roll them briskly between your palms until the fibres felt into one continuous thread.
Mga materyales para sa hakbang na ito:
Ikid ng Sinulid na Lana1 pirasoMga kailangang kasangkapan:
Karayom sa nalbinding8
8
Shape the tube
Shape the tube
Increase by working two stitches into one loop and decrease by skipping a loop, shaping the tube — narrowing for an ankle, turning a heel, or rounding a mitten — as the piece requires.
Mga kailangang kasangkapan:
Karayom sa nalbinding9
9
Close the toe
Close the toe
At the end, decrease steadily until only a few loops remain, then pass the needle through them and draw them tight to close the toe or mitten tip.
Mga kailangang kasangkapan:
Karayom sa nalbinding10
10
Secure and trim the tail
Secure and trim the tail
Weave the final yarn tail back through several stitches on the inside to lock it, then trim it flush. Because the fabric is looped, not knitted, it cannot unravel from the cut end.
Mga kailangang kasangkapan:
Karayom sa nalbindingGuntingMga Materyales
1- 1 pirasoPlaceholder
Mga Materyales ng Nakakonektang Blueprint
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.