SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Microscope Slides Cut from Sheet, Coverslips from a Blown Bubble
Bubbles

Nilikha ni

Bubbles

14. Oktubre 2026IT
21
0
0
0
0

Microscope Slides Cut from Sheet, Coverslips from a Blown Bubble

A microscope slide is a strip of plain glass about 75 × 25 mm and 1 mm thick with smoothed edges; a coverslip is a much thinner square that presses the specimen flat. Cut the slides from thin sheet and grind the edges; for coverslips, blow a thin bubble on a glass tube and cut flat pieces from it. The picture: a tray of early 20th-century prepared slides under coverslips, museum of the Institut Pasteur de Lille.
Katamtaman
An afternoon

Mga Tagubilin

1

Cut the slides

Mark thin glass sheet in 25 mm strips, score and snap them, then score and snap each strip at 75 mm.

Mga materyales para sa hakbang na ito:

Plantsa ng salaminPlantsa ng salamin1 piraso

Mga kailangang kasangkapan:

Panghiwa ng salaminPanghiwa ng salamin
RulerRuler
Salaming pangkaligtasanSalaming pangkaligtasan
2

Grind the edges

Rub every edge and corner on a flat glass plate with wet fine grit until smooth to the touch. Wash and dry.

Mga materyales para sa hakbang na ito:

Butil ng silicon carbideButil ng silicon carbide20 g
TubigTubig1 litro

Mga kailangang kasangkapan:

Digital na Kalibrador 6 PulgadaDigital na Kalibrador 6 Pulgada
3

Blow a thin bubble

Close the end of a glass tube in the torch, heat it evenly and blow a large, very thin bubble, turning it as you blow (our method).

Mga materyales para sa hakbang na ito:

Kit ng mga Tubong SalaminKit ng mga Tubong Salamin1 piraso

Mga kailangang kasangkapan:

Pang-ihip ng salamin na pang-mesaPang-ihip ng salamin na pang-mesa
Salaming pangkaligtasanSalaming pangkaligtasan
Guwantes na Matibay sa InitGuwantes na Matibay sa Init
4

Cut coverslips

When cold, break the bubble and pick the flattest pieces from its sides. Trim them to small squares with the cutter and check the thickness with the caliper; keep only even, thin pieces.

Mga kailangang kasangkapan:

Panghiwa ng salaminPanghiwa ng salamin
Digital na Kalibrador 6 PulgadaDigital na Kalibrador 6 Pulgada
Salaming pangkaligtasanSalaming pangkaligtasan
5

Store clean

Wash slides and coverslips and keep them apart in a closed jar so they stay free of dust and grease.

Mga materyales para sa hakbang na ito:

TubigTubig1 litro

Mga kailangang kasangkapan:

Garapong SalaminGarapong Salamin
6

Slides from a sheet

Naglo-load ng Jupyter notebook…
7

Limits

Slide size and edge finish are as Wikipedia gives them; the blown-bubble coverslips are our method. Blown coverslips vary in thickness: measure them, since the wrong thickness blurs high-power images.

Mga Materyales

4

Mga Kinakailangang Kasangkapan

7

Ang blueprint na ito ay gumagawa ng

Kaugnay na Blueprint

Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...