Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Oriented Barium Ferrite Disc Magnet: Heated to 500 °C Without a Field (Gorter, Philips 1956, Ex. 6)
A ceramic magnet oriented in the die as in Example 4, but heated to 500 °C with no second field before sintering at 1280 °C. In the principal direction it held 3,025 gauss with a coercive force of 1,550 oersted and a (BH)max of 1.58 × 10⁶.
Source: E. W. Gorter, G. W. Rathenau and A. L. Stuyts (Philips), US 2,762,778 (1956), Example 6. They made blocks; disc size is ours. Picture: ferrite magnets, Omegatron, Wikimedia Commons, CC BY-SA 3.0.
Abantado
3 days
Mga Tagubilin
1
1
Weigh barium carbonate and iron oxide
Weigh barium carbonate and iron oxide
Weigh 450 g barium carbonate and 2000 g ferric oxide. Barium carbonate is poisonous if swallowed: gloves and a dust respirator.
Mga materyales para sa hakbang na ito:
Barium carbonate (witherite)450 g
Ferric oxide2000 gMga kailangang kasangkapan:
Timbangang panimbang
Gwantes na goma
Panala sa Hininga na P1002
2
Mill 20 hours under alcohol, dry
Mill 20 hours under alcohol, dry
Grind the mixture in a ball mill under alcohol for 20 hours, then dry it.
Mga kailangang kasangkapan:
Gilingang Bolang Bakal
Etanol - antas laboratoryo, 95 %
Hurnong pantuyo3
3
Pre-fire: through a 1100 °C zone in 10 minutes
Pre-fire: through a 1100 °C zone in 10 minutes
Pass the dry powder at 20 mm per minute through an electric furnace with a 20 cm hot zone at 1100 °C, in air: 10 minutes in the heat. Let it cool.
Mga kailangang kasangkapan:
Hurnong Tubo
Krisol na may takip (porselana)
Guwantes na Matibay sa Init4
4
Grind 12 hours with alcohol, dry
Grind 12 hours with alcohol, dry
Pulverise the pre-fired material in a ball mill with alcohol for 12 hours, then dry it. This is the pre-fired powder.
Mga kailangang kasangkapan:
Gilingang Bolang BakalEtanol - antas laboratoryo, 95 %Hurnong pantuyo5
5
Stir into 8 % polyvinyl acetate in acetone
Stir into 8 % polyvinyl acetate in acetone
Dissolve polyvinyl acetate in acetone to a 8 % solution and stir the pre-fired powder into it, 1 cc of solution per gram of powder. The binder burns off later.
Mga kailangang kasangkapan:
Polyvinyl acetate
AcetoneTimbangang panimbang6
6
Orient in a 10000 oersted field
Orient in a 10000 oersted field
Put the suspension in a moulding die between the poles of a magnet and apply a first field of 10000 oersted. Remove the binder solution while the field is on (as in Example 4).
Mga kailangang kasangkapan:
Hulmahan sa pagpindot ng disk
Elektromagneto
Haydroliko na pandiin7
7
Heat to 500 °C without a field
Heat to 500 °C without a field
Heat the blocks to 500 °C with no magnetic field.
Mga kailangang kasangkapan:
Hurnong TuboGuwantes na Matibay sa Init8
8
Sinter: through a 1280 °C zone in 5 minutes
Sinter: through a 1280 °C zone in 5 minutes
Pass the block at 20 mm per minute through an electric furnace in air at 1280 °C with a 10 cm hot zone: about 5 minutes in the heat.
Mga kailangang kasangkapan:
Hurnong TuboGuwantes na Matibay sa Init9
9
Magnetise in the principal direction
Magnetise in the principal direction
Magnetise the block along the direction of the first field, the principal direction. The patent magnetises it in a field in that direction; ours: an electromagnet. Find the north face with a compass.
Mga kailangang kasangkapan:
Elektromagneto
KompasMga Materyales
2- Placeholder
- 2000 gPlaceholder
Mga Kinakailangang Kasangkapan
15- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.