Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Propane from Natural Gas: Oil Absorption, then Fractional Condensation under Pressure (Garner and Cooper, US 1,307,353)
Charlie

Nilikha ni

Charlie

4. Nobyembre 2026DE
3
0
0
0
0

Propane from Natural Gas: Oil Absorption, then Fractional Condensation under Pressure (Garner and Cooper, US 1,307,353)

A liquefied fuel gas must be one pure substance: a mixture gives a changing pressure and heating value as the flask empties. James B. Garner and Howell C. Cooper of the Hope Natural Gas Company (filed 1916, US 1,307,353) took the light gases out of natural gas with an absorbing oil, freed them from the gasoline, scrubbed out the last heavier vapours, and then split the butane-propane mixture by pressure alone: pumped into a long sloping pipe, the butane liquefied first and was drawn off; the propane left behind was compressed with water until it liquefied too. Not given: sizes (beyond their field pipe), flow rates and the absorber pressure. Source: J. B. Garner and H. C. Cooper, US 1,307,353 (1919). Picture: their three drawing sheets.
Abantado
Continuous (industrial)

Mga Tagubilin

1

Read US 1,307,353

"We continue to pump into this compression-chamber quantities of the gas to be reduced until, in consequence of increasing pressure, a liquefaction has taken place. ... this initial liquefaction is a liquefaction of the butane component alone, the propane component remaining at this pressure a gas."
2

Absorb the light vapours

Compress the natural gas from the wells, cool it, and bubble it through perforated pipes in two absorbers of absorbing oil (a petroleum hydrocarbon of 28 to 55 degrees Baume at 60 F), the oil flowing through them against the gas. The gas that is not absorbed goes on to the gas line.

Mga materyales para sa hakbang na ito:

Likas na gasLikas na gas1 continuous feed
Hindi kilalang materyalHindi kilalang materyal1 as required

Mga kailangang kasangkapan:

Kompresor ng gasKompresor ng gas
Heat exchangerHeat exchanger
Pansipsip ng gasPansipsip ng gas
3

Drive off the light gases

Run the enriched oil through a liquid trap into a primary still heated by steam pipes, at about the absorbers' pressure and a low temperature, about 95 to 110 F. Only the constituents that are gases at ordinary pressure and temperature, butane and propane among them, distil off.

Mga kailangang kasangkapan:

Destilador na pinaiinit ng singawDestilador na pinaiinit ng singaw
Boiler ng singawBoiler ng singaw
4

Take out the gasoline

Pass the oil through a reducing valve and a heat exchanger into a second steam still at lower pressure and higher temperature. The gasoline (pentane to octane) distils over and condenses in cooled coils into closed storage tanks; the butane and propane stay as gas above it.

Mga kailangang kasangkapan:

Destilador na pinaiinit ng singawDestilador na pinaiinit ng singaw
Heat exchangerHeat exchanger
Ikid ng kondensadorIkid ng kondensador
Tangke ng langisTangke ng langis
5

Scrub the butane and propane

Bubble the remaining gas through supplemental absorbers of "sun spirits" (a paraffin hydrocarbon of about 33.7 degrees Baume at 60 F), at about atmospheric pressure. They hold back any pentane or heavier vapour, and a mixture of nearly pure butane and propane comes off.

Mga materyales para sa hakbang na ito:

Hindi kilalang materyalHindi kilalang materyal1 as required

Mga kailangang kasangkapan:

Pansipsip ng gasPansipsip ng gas
6

Liquefy the butane

Pump the mixture, with rising pressure, into a long strong pipe laid up a slope (in the field theirs was a 5-inch pipe 125 feet long), opening its pet cocks now and then to find liquid. With their mixture (butane and propane in about equal weights) the butane alone liquefied at about 130 lb per square inch and was drawn off from the lower end into a tank.

Mga kailangang kasangkapan:

Silid na pampalikidoSilid na pampalikido
Kompresor ng gasKompresor ng gas
Panukat ng DiinPanukat ng Diin
Tangke ng gas na may presyonTangke ng gas na may presyon
Salaming pangkaligtasanSalaming pangkaligtasan
7

Liquefy the propane

Close the inlet and force water into the lower end of the chamber. The rising water compresses the propane left in the upper end; the patent says it liquefied at about 650 lb per square inch. Open the outlet at the top and let the water drive the liquid propane through a cooler into a pressure cylinder, until the water shows at the top pet cock.

Mga materyales para sa hakbang na ito:

TubigTubig1 as required

Mga kailangang kasangkapan:

Bombang pandiinBombang pandiin
Silid na pampalikidoSilid na pampalikido
Heat exchangerHeat exchanger
Tangke ng gas na may presyonTangke ng gas na may presyon
Panukat ng DiinPanukat ng Diin
8

The patent drawings

US 1,307,353, sheets 1-3: compressor, cooler and absorbers with the primary still (Fig. 1), the gasoline still, condensing coils, storage tanks and supplemental absorbers (Fig. 2), and the compression chamber with its pet cocks, gauge and the butane and propane tanks (Fig. 3). Public domain (expired patent).
9

History and honest limits

Garner and Cooper filed on 5 August 1916 for the Hope Natural Gas Company of Pittsburgh; the patent was granted on 24 June 1919. They wrote that butane and propane could not be separated by compressing the natural gas itself, only after the light pair had been isolated. The pressures (about 130 lb and about 650 lb) are those the patent reports for its own equal-weight mixture at field temperature; they say other proportions or temperatures change them. The absorbing oil and the sun spirits are given only by kind and gravity (unknown). Propane and butane are flammable gases held under pressure.

Mga Materyales

3
  • 1 continuous feed
    Placeholder
  • Placeholder
  • 1 as required
    Placeholder

Mga Kinakailangang Kasangkapan

12

Ang blueprint na ito ay gumagawa ng

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...