Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Rubber Squeeze Bulb: Latex Coagulated Inside a Split Mould Coated with Calcium Nitrate (Szegvari, Anode, US 1,949,502)
A seamless hollow rubber bulb grows inside a closed mould: the cavity is coated with a coagulant, the mould is filled with latex, and rubber sets on the walls until it is thick enough. The rest of the latex is poured out through the neck.
Result: a seamless rubber squeeze bulb with a neck; ours sized at about 60 ml.
Source: Szegvari, US 1,949,502 (American Anode, 1934); his example is a football bladder. Not given: times, strengths, vulcanising details. Picture drawn by Youblob.
Katamtaman
2 days
Mga Tagubilin
1
1
Coat the mould cavity with calcium nitrate in acetone
Coat the mould cavity with calcium nitrate in acetone
Open the split mould and coat only the cavity with a solution of calcium nitrate in acetone, by brush or spray. The acetone evaporates and leaves a sticky film of coagulant. Ours: a cavity of about 60 ml with a neck.
Mga kailangang kasangkapan:
Nitrate ng kaltsiyo
Acetone
Hulmahang hati para sa bola
Malapad na brotsa2
2
Close the mould under the latex
Close the mould under the latex
Lower both halves under the surface of latex and close them once they are submerged and the air bubbles are gone. Rubber now sets on the coated walls; the longer the contact, the thicker the wall.
Mga materyales para sa hakbang na ito:
Likas na latex ng goma1 as requiredMga kailangang kasangkapan:
Malaking Kaldero3
3
Pour out the extra latex through the neck
Pour out the extra latex through the neck
Lift the mould out and turn it over so the liquid latex drains back through the neck. Refill with water holding a little acetic acid so the inner face sets too.
Mga kailangang kasangkapan:
Acetic acid (glacial)
Tubig4
4
Open under warm water and leach
Open under warm water and leach
Open the mould under running warm water, take out the bulb and leave it in the water until most of the soluble matter has leached out. Clean any liquid latex off with dilute ammonia.
Mga kailangang kasangkapan:
Tubig
Solusyon ng ammonia - manipis5
5
Inflate lightly and dry
Inflate lightly and dry
Drain the bulb, inflate it lightly so it does not collapse, and dry it at room temperature or in a drying cabinet. The latex may hold sulphur and be vulcanised in the usual way; Szegvari gives no details.
Mga kailangang kasangkapan:
Hurnong pantuyoMga Materyales
1- 1 as requiredPlaceholder
Mga Kinakailangang Kasangkapan
9- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.