Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Heil and Esch · Public domain (1909)
Rubber Stoppers: Pará Rubber with Ceresine, Moulded and Cured (Heil & Esch 1909)
Laboratory rubber stoppers from a 1909 rubber factory's book of mixings: Pará rubber with ceresine wax, sulphur and magnesia, run out as a cord, cut to weight, pressed into moulds and cured.
Source: Heil & Esch, The Manufacture of Rubber Goods (1909), mixing No. 34 (p. 108) and the stopper method (p. 135). They give no cure time or temperature. Using smoked ball rubber as their Pará, and the mill, clamps and steam vessel, are ours. Picture: their page of mixings.
Katamtaman
1 day
Mga Tagubilin
1
1
Weigh mixing No. 34
Weigh mixing No. 34
Weigh out 10,000 g Pará rubber, 2,000 g ceresine, 1,000 g sulphur and 100 g calcined magnesia (magnesia usta).
Mga materyales para sa hakbang na ito:
Pinausukang bolang goma10000 g
Pagkit na ceresine2000 g
Pulbos na asupre1000 g
Oksido ng magnesiyo100 gMga kailangang kasangkapan:
Timbangang panimbang2
2
Mix on the rolls
Mix on the rolls
Work the rubber on the mixing rolls and work the ceresine, sulphur and magnesia into it until the mixing is even.
Mga kailangang kasangkapan:
Two-roll na gilingan ng goma3
3
Run a cord on the tube machine
Run a cord on the tube machine
Run the mixing through the tube machine as a cord of a size to suit the stoppers. It must be free from air bubbles, or the stoppers will be faulty after curing.
Mga kailangang kasangkapan:
Makina sa tubong goma4
4
Cut pieces to weight
Cut pieces to weight
Cut the cord into pieces of the exact weight of one stopper plus 2 or 3 per cent, for what squeezes out of the mould.
Mga kailangang kasangkapan:
Kutsilyong Pang-arteTimbangang panimbang5
5
Press into moulds and clamp
Press into moulds and clamp
Press each piece into a mould and clamp the small moulds very tightly in iron clips.
Mga kailangang kasangkapan:
Molde sa pag-vulcanize
Klamp na hugis-C6
6
Cure in steam
Cure in steam
Cure the clamped moulds in a steam heater (Heil & Esch also name the sulphur bath). They give no time or temperature for stoppers; then open the moulds and take out the stoppers.
Mga kailangang kasangkapan:
Autoclave na pang-mesaMolde sa pag-vulcanizeMga Materyales
4- 10000 gPlaceholder
- 2000 gPlaceholder
- 1000 gPlaceholder
- 100 gPlaceholder
Mga Kinakailangang Kasangkapan
7- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.